Challenge 130TC-A-160000 Скачать руководство пользователя страница 225 | Manualshive

Страница: 225 / 282

background image

MAY 2019

CMT-130TC Book Trimmer

6-11

6. General Procedures/Information

GP 6.10 Micro-Switches

Micro-switches are small, lever-operated, me-
chanical switches. They are used in the Eleva-
tor/Tilt Conveyor and Stacker accessories.
When the lever is actuated, it either closes or
opens the contacts within the switch, depending
on where it is used.

Procedure

1.

Switch the main power ON and click the “Di-
agnostic” button to bring up the diagnostic
screen. Click on the applicable accessory
diagnostic button to bring up the

accessory’s

diagnostic screen.

2. Actuate the switch on and off by manually

pressing the actuator arm and releasing it. If
the switch and main PWB are working cor-
rectly, an audible tone will be emitted from
the main PWB. Does the switch change
state properly?

Y N

Perform the RAP associated with the spe-
cific switch.

3. Switch the main power OFF and lockout

power to the machine.

WARNING

Disconnect and lockout power as described
in the Power Lockout Procedure on page ix.
There can be 120VAC at the micro-switches!

4. Loosen the switch mounting screws or

bracket screws.

5. Adjust the switch or bracket such that the

switch clicks when actuated, and clicks
again when unactuated.

6. With the switch in its proper position, tighten

the mounting screws.

7.

Switch the main power ON and click the “Di-
agnostic” button to bring up the diagnostic
screen. Click on the applicable accessory
diagnostic button to bring up the accessory’s
diagnostic screen.

8. Actuate the switch on and off use the actuat-

ing devise (door, bracket, etc.) to actuate the
switch. If the switch and main PWB are
working correctly, an audible tone will be
emitted from the main PWB. Does the
switch change state properly?

Y N

Readjust switch and/or actuator and repeat
this test until the switch functions as it does
when actuated manually.

The switch adjustment is complete.

Figure 6-13. Micro-Switches

«
...
223
224
225
226
227
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Watkiss Страницы: 84

Бренд: Oce Страницы: 62

Бренд: Flo Страницы: 56

Бренд: Little Wonder Страницы: 4

Бренд: Nordic Страницы: 12

Бренд: Texas Equipment Страницы: 20

Decora Smart DG6HD

Бренд: Leviton Страницы: 16

Бренд: GreenWorks Pro Страницы: 28

Бренд: Power Plus Страницы: 9

Бренд: Jonsered Страницы: 27

Бренд: Jonsered Страницы: 35

Бренд: Shindaiwa Страницы: 60

Бренд: LIVERYMAN Страницы: 4

Бренд: Tanaka Страницы: 16

BEST 710 DPG-5 IN 1

Бренд: Garland Страницы: 172

Бренд: Tanaka Страницы: 36

Бренд: Echo Страницы: 36

Бренд: Husqvarna Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды