manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 80

 

 

 

MAY 2019 

 

2. Status Indicator RAPs

 

2-68 

CMT-130TC Book Trimmer 

RAP 2.60 Book Entering Elevator 
Sensor 

Elevator I/O PWB Input 7 

The book in Elevator sensor is a retro-reflective 
sensor that detects books as they enter the Ele-
vator.  The sensor is mounted near the bottom 
of the Elevator, just above where books travel 
into the Elevator (Figure 2-91).  The reflector is 
located on the Tilt Conveyor (Figure 2-92). 

Possible Fault Indicators 

 

“Elevator Book on Tilt Error”

 

is displayed erroneously. 

 

A jam is not detected when there is a 
jam. 

Initial Actions 

Check that the reflector is in place (Figure 2-92). 
Replace if necessary (PL 5.41 Tilt Conveyor 
56600TCA (3/8)). 

Check that all cables between the trimmer, Ele-
vator, and Tilt Infeed Conveyor are securely fas-
tened and are not damaged. 

Check and repair loose or damaged wires 59, 
73, and 74 at the Elevator electrical panel. 

Procedure 

1.  Switch the main power ON and go to the El-

evator diagnostic screen (GP 6.2 Input/Out-
put Diagnostics).  Make sure that the sensor 
and reflector are not obstructed.  Is input 
“Book In Elevator” off? 

Y  N 

Disconnect wire 59.  On the diagnostic 
screen does input “Book In Elevator” switch 
off? 

Y  N 

Disconnect power and replace the Ele-
vator I/O PWB (REP 4.26 Accessory 
PWB Replacement). 

Adjust the sensor (GP 6.6 Retro-reflective 
Sensors) and replace if faulty (PL 5.31 Ele-
vator 56421TCA (4/7) or PL 5.37 Elev. Elec-
trical Panel EE-3523). 

2.  Short wire 59 to 74.  On the diagnostic 

s

creen does input “Book In Elevator” switch 

on? 

Y  N 

Disconnect power and replace the Elevator 
I/O PWB (REP 4.26 Accessory PWB Re-
placement). 

3.  Adjust the sensor (GP 6.6 Retro-reflective 

Sensors) and replace if faulty (PL 5.31 Ele-
vator 56421TCA (4/7) or PL 5.37 Elev. Elec-
trical Panel EE-3523). 

 

Figure 2-91. Book Entering Elevator Sensor 

 

Figure 2-92. Reflector 

 

 

Figure 2-93. Elevator Electrical Panel 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды