Challenge 130TC-A-160000 Скачать руководство пользователя страница 226 | Manualshive

Страница: 226 / 282

background image

MAY 2019

6. General Procedures/Information

6-12

CMT-130TC Book Trimmer

GP 6.11 Keyed Interlock Switches

Keyed interlock switches are used throughout
the CMT-130TC and accessories. They prohibit
operation of the machine whenever an inter-
locked door or panel is open. A key mounted to
the door or panel must be completely inserted
into its corresponding switch in order for the ma-
chine to run. Use the following procedure to ad-
just the keyed interlock switches.

Procedure

1.

Switch the main power ON and click the “Di-
agnostic” button to bring up the diagnostic
screen. If applicable, click on an accessory
diagnostic button to bring up a specific ac-
cessory’s diagnostic screen.

2. Actuate the switch on and off by inserting

and removing a test key (part number
45180-4). If the switch and main PWB are
working correctly, an audible tone will be
emitted from the main PWB. Does the
switch change state properly?

Y N

Go to RAP 2.11 Interlock Test

3. Switch the main power OFF.

4. Loosen the switch mounting and/or bracket

screws or actuator key mounting screws.

5. Adjust the switch and key such that when

the door is closed, the actuator key inserts
fully into the switch body, and when the door
is opened, the actuator key pulls out of the
switch body.

6. With the switch and key in their proper posi-

tions, tighten all mounting screws.

7. Switch the main power O

N and click the “Di-

agnostic” button to bring up the diagnostic
screen. If applicable, click on an accessory
diagnostic button to bring up a specific ac-
cessory’s diagnostic screen.

8. Actuate the switch on and off by opening

and closing the door. If the switch and main
PWB are working correctly, an audible tone
will be emitted from the main PWB. Does
the switch change state properly?

Y N

Readjust switch body and/or actuator key
and repeat this test until the switch functions
as it did using the test key.

The switch adjustment is complete.

Figure 6-14. Keyed Interlock Switch

«
...
224
225
226
227
228
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Fellowes Страницы: 3

Ripley SDT Series

Бренд: Cablematic Страницы: 2

Бренд: Cocraft Страницы: 76

Бренд: Echo Страницы: 44

Бренд: Echo Страницы: 28

Garden Groom "PRO"

Бренд: JML Страницы: 6

Бренд: Stiga Страницы: 2

Бренд: Echo Страницы: 28

Бренд: Husqvarna Страницы: 76

Poulan Pro 545192174

Бренд: Poulan Pro Страницы: 2

Бренд: Poulan Pro Страницы: 14

Бренд: Poulan Pro Страницы: 17

Бренд: Poulan Pro Страницы: 19

Бренд: Poulan Pro Страницы: 15

Бренд: Poulan Pro Страницы: 7

Бренд: Challenge Xtreme Страницы: 2

Бренд: Challenge Xtreme Страницы: 18

Бренд: Cub Cadet Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды