manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 135

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

4-29 

4. Repair/Adjustment Procedures

 

REP 4.24 Console PWB Replacement 

The following procedure outlines the steps nec-
essary to replace the console PWB.  The con-
sole PWB stores machine-specific data such as 
calibration data, jobs, and machine settings that 
should be backed up before replacing the con-
sole PWB. Backup instructions are included in 
the procedure below. 

CAUTION 

Observe standard ESD protection procedures 
while replacing any PWB's.  Damage may result 
due to static discharge. 

Procedure 

1.  If there are jobs stored in machine memory 

that you would like to keep, turn the power 
off, insert a USB flash drive in the machine, 
turn the power back on.  Press the green 
start button and go to the jobs screen. Click 
the "Copy All" button and follow the prompts 
on the screen to copy the jobs to the USB 
drive. 

Important! Backup stored machine settings 
and parameters as follows:  

2.  Insert a USB flash drive into the console and 

switch the main power ON.  

3.  P

ress the “Setup” button to bring up the 

setup options, then p

ress the “Service Info” 

tab to open the Service Info screen.  Click 
on th

e “Enable Tabs Code” text box, enter in 

the code 

6125

 and press enter.  This will un-

lock all of the locked tabs. 

4. 

Press the “Options & Updates” tab to open 
the Options and Updates screen. 

5. 

Click on “Save USB Params” and follow 
prompts on the screen. 

6.  As an extra precaution, it may be helpful to 

take pictures and/or write down the settings 
shown in all seven of the Setup 
tabs/screens. 

7.  Switch the main power OFF and lockout 

power to the machine. 

WARNING 

Disconnect and lockout power as described 
in the Power Lockout Procedure on page ix. 

8.  Remove the eight screws holding the display 

console in place. 

9.  Pull the top of the console assembly out-

ward while laying the console flat, until the 
bottom of the console assembly hangs from 
the opening in the top/front cover. 

10.  Disconnect all cable connectors from the 

main PWB. 

11.  Remove the four nuts that mount the PWB 

to standoffs on the console (Figure 4-42). 

12.  Carefully remove the new PWB from the 

electro-static bag that it was shipped in, and 
place the old PWB in the empty bag. 

13.  Install the new PWB on the four standoffs on 

the electrical panel, and attach it securely 
with all four nuts. 

14.  Securely connect all cables to the new 

PWB. 

15.  Carefully place the console assembly back 

into position, making sure not to pinch any 
cables when doing so. 

16.  Attach the console assembly with the eight 

screws holding it in place 

17.  To restore machine settings and parameters 

that was backed up earlier, insert the USB 
flash drive with the backup file on it into the 
front console. 

18.  Restore power to the machine and switch 

the main power ON. 

19. 

Press the “Setup” button to bring up the 
setup options, then p

ress the “Service Info” 

tab to open the Service Info screen.  Click 
on the “Enable Tabs Code” text box, enter in 
the code 

6125

 and press enter.  This will un-

lock all of the locked tabs. 

20. 

Press the “Options & Updates” tab to open 
the Options and Updates screen. 

21. 

Click on “Load USB Params” and follow 
prompts on the screen. 

22.  Make sure that the settings in all seven 

setup tabs/screens match those recorded 
earlier. 

23.  Run a few test books through the trimmer to 

make sure everything is working properly. 

 

 

Figure 4-42. Console PWB 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды