manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 68

 

 

 

MAY 2019 

 

2. Status Indicator RAPs

 

2-56 

CMT-130TC Book Trimmer 

RAP 2.48 Book Width Sensor 

Input 28 

The book width sensor is a retro-reflective sen-
sor that detects the face edge of books as they 
enter into the registration area.  The trimmer 
uses this sensor to automatically determine the 
starting width of a book without the need for the 
user to enter in the dimension. The sensor is 
mounted to the registration assembly and the re-
flector is mounted to the table in a square indent 
(Figure 2-73). 

Possible Fault Indicators 

 

“Book Width Error”

 message is 

displayed. 

 

The face jogger repeatedly does not 
align with the face edge of the books 
properly during registration. 

Initial Actions 

Check that the reflector on the table in the 
square indent is properly installed and not ob-
structed.  Replace if faulty (PL 5.10 Main As-
sembly 59000 (10/14)). 

Check for loose or damaged wire 82 at the elec-
trical panel. 

Procedure 

1.  Make sure that both the sensor and the re-

flector are not obstructed.  Switch the main 
power ON and go to the diagnostic screen 
(GP 6.2 Input/Output Diagnostics). Does the 
diagnostic screen show input “Book Width” 
switched on? 

Y  N 

Short wire 82 to 74 at the main PWB.  On 
the diagnostic screen does input "Book 
Width" switch on? 

Y  N 

Disconnect power and replace the con-
sole PWB (REP 4.24 Console PWB Re-
placement). 

Adjust the sensor (GP 6.6 Retro-reflective 
Sensors) and replace if faulty (PL 5.17 
Power Panel EE-3503 (2/2)). 

2.  Disconnect wire 82.  On the diagnostic 

screen does input "Book Width" switch off? 

Y  N 

Disconnect power and replace the console 
PWB (REP 4.24 Console PWB Replace-
ment). 

3.  Adjust the sensor (GP 6.6 Retro-reflective 

Sensors) and replace if faulty (PL 5.17 
Power Panel EE-3503 (2/2)). 

 

 

Figure 2-73. Book Width Sensor 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды