Challenge 130TC-A-160000 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 282

background image

MAY 2019

CMT-130TC Book Trimmer

2-43

2. Status Indicator RAPs

RAP 2.35 Gripper Transport Servo
Motor

Input 37, Outputs 33, 34, 35

The gripper transport servo motor controls the
linear motion of the gripper transport. It is lo-
cated beneath the conveyor belt area, at the
front end of the gripper transport (Figure 2-55).

Possible Fault Indicators



The gripper will not move properly.



“Linear Position Err.”

Message

occurs repeatedly.

Initial Actions

Check for loose or damaged wires 32, 56, 57,
and 58 at the main PWB.

Check for proper connection of the power cable
between the electrical panel and the servo mo-
tor.

Check for proper connection of the signal cable
between the main PWB and the servo motor.

Procedure

1. Switch the main power ON. Is there 53 VAC

between wire 19 at the IR relay and wire 80
at BR2 (Figure 2-56)?

Y N

Is circuit breaker CB7 tripped or off?

Y N

Go to RAP 2.5 DC Power.

Reset circuit breaker CB7 if tripped. If circuit
breaker continues to trip, use applicable
schematic to troubleshoot affected circuit
(Section 7, Wiring Data).

2. Go to the diagnostic screen and enable out-

puts (GP 6.2 Input/Output Diagnostics).

Make sure all doors are closed, then acti-
vate the Interlock Relay output. Press the
green start button to energize the IR relay.
The “Interlock Relay IR” input should switch
on. Is there 53 VAC between wires 79 and
80 at the bridge rectifier BR2?

Y N

Go to RAP 2.12 Interlock Relay.

3. Is there 75 VDC between wires 54 and 55 at

BR2?

Y N

Check and repair wires 54, 55, 79, and 80.
Check for an open diode on BR2. Replace
BR2 if defective (PL 5.16 Power Panel EE-
3503 (1/2)).

4. With the IR relay activated, check the indica-

tor light on the bottom of the servo motor. Is
the light on at all, either green or yellow,
flashing or solid?

Y N

Check and repair the power cable that in-
cludes wires 54 and 55 at the electrical
panel. If this does not fix the problem, dis-
connect power and replace the servo motor
(PL 5.9 Main Assembly 59000 (9/14)).

5.

In the diagnostic screen, press the “Gripper
Test” button. Did the gripper run through a
series of movements and did the indicator
light on the servo motor turn green?

Y N

Check and repair the signal cable that in-
cludes wires 32, 56, 57, and 58 at the main
PWB. If problem still exists, disconnect
power and replace the main PWB (REP 4.23
Main PWB Replacement). If problem still ex-
ists, disconnect power and replace the servo
motor (PL 5.9 Main Assembly 59000 (9/14)).

Repair complete.

Figure 2-55. Gripper Transport Servo Motor

Figure 2-56. Electrical Panel Connections

«
...
53
54
55
56
57
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Weed Eater Страницы: 11

Бренд: Amos Страницы: 10

Бренд: GreenWorks Страницы: 28

Бренд: Elko Страницы: 30

Бренд: EINHELL Страницы: 76

Бренд: Parkside Страницы: 191

Бренд: Jata Страницы: 24

Бренд: Ryobi Страницы: 20

Бренд: Texas A/S Страницы: 20

Бренд: Status Страницы: 40

Generation 3 507

Бренд: Dahle Страницы: 8

START-LINE ACC-250-LD

Бренд: Trust Страницы: 52

Бренд: Powerplus Страницы: 11

GCBE18VCR-LI10L

Бренд: Gardeo Страницы: 41

EasyCut Li-18/50

Бренд: Gardena Страницы: 14

Бренд: Makita Страницы: 128

Бренд: Makita Страницы: 88

Бренд: Makita Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды