Challenge 130TC-A-160000 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 282

background image

MAY 2019

4. Repair/Adjustment Procedures

4-32

CMT-130TC Book Trimmer

ADJ 4.27 Elevator Pusher Height

The height of the pusher plate in the Elevator
can be adjusted. The consistency with which
books are pushed into the trimmer is partially
dependent on the adjustment of the pusher
plate.

Initial Actions

Check that the top shelves of the Elevator are
properly stopping at 36" (91.4 cm) from the floor
or level with the trimmer

’s internal conveyor

belts. If not, see the

Installation and Operator's

Manual

for proper setup.

Procedure

1. Wait until the Elevator shelves are not mov-

ing then switch the main power to the trim-
mer OFF. Lockout power to the trimmer.

2. Switch the main air OFF.

3. Open the top cover of the Elevator.

4. Loosen the two screws that mount the

pusher plate to the pusher bracket (Figure
4-45).

5. Push the plate to the edge of the lift plates.

6. Adjust the height of the pusher plate such

that the brushes interfere with the lift plates
by approximately 1/8" (3 mm) as shown in
Figure 4-45.

7. Tighten the pusher plate mounting screws.

Make sure the bottom edge of the pusher
plate is not crooked relative to the lift plates.

8. Check operation of the pusher plate by slid-

ing the pusher across the lift plates.

9. Return the pusher to its home position.

10. Close the top cover.

11. Restore power to the trimmer then switch

the main power ON and main air ON.

12. Run a few test books through the Elevator to

make sure the pusher is working properly.

Figure 4-45. Pusher Plate Adjustment

«
...
136
137
138
139
140
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Makita Страницы: 3

Бренд: VS Sassoon Страницы: 12

Бренд: Villager Страницы: 81

Бренд: Cramer Страницы: 144

decora IP710-LF

Бренд: Leviton Страницы: 2

Бренд: Leviton Страницы: 2

Бренд: Ergotools Pattfield Страницы: 60

Бренд: Meec tools Страницы: 25

Бренд: Weed Eater Страницы: 11

Бренд: F&F Страницы: 7

Бренд: SHARKS Страницы: 97

Бренд: P.Lindberg Страницы: 70

Бренд: Flymo Страницы: 12

Бренд: Ozito Страницы: 6

BUMO & FEED Eco4

Бренд: Tanaka Страницы: 44

Бренд: XTline Страницы: 58

Бренд: HUSLOG Страницы: 17

Бренд: Tanaka Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды