Fluorescent and LED Fixture Slide Dimmer
Single Pole (One location) or 3-Way (Multi-location)
Cat. No. IP710-LF
1200VA-120VAC, 60Hz, 1500VA-277VAC, 60Hz
For Use with LED fixtures using 0-10V dimmable power supply/drivers,
Advance Transformer Mark 7
®
OSRAM Sylvania Quicktronic
®
Helios™ or equivalent dimmable ballasts.
IMPORTANT:
For 3-way applications, note that one of the
screw terminals from the old switch being removed will usually
be a different color (Black) or labeled Common. Tag that wire
with electrical tape and identify as the common (Line or Load)
in both the dimmer wall box and the standard 3-way switch
wall box.The remaining two wires on the brass or lighter screw
terminals of the old switch are the travelers.
Step 1
NOTE:
If the wiring in the wall box does not resemble any of
these configurations, consult an electrician.
Identifying your wiring application
(most common):
WARNINGS:
•
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING OR
SERVICING FIXTURE!
•
To avoid overheating
and possible damage to this device and other equipment, use only with the appropriate LED 0-10V dimmable power supplies/drivers,
Advance Transformer 120/277V Mark 7
®
0-10V ballasts or OSRAM Sylvania Quicktronic
®
Helios™ electronic ballasts.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
CAUTIONS:
• If you are unsure about any part of these instructions, consult an electrician.
• Use only one (1) dimmer in a 3- or 4-way circuit. The switch(es) will turn the light on at the brightness level selected at the dimmer.
• Lighting fixture and dimmer must be grounded.
• Use this device only with copper or copper clad wire.
• To avoid damage to the product,
DO NOT
use disinfecting products, including foggers, sprays or other types of atomized cleaning agents.
•
DO NOT
spray liquid onto the product.
• To clean use a damp cloth with mild soap.
DI-221-IP710-01A
Tools needed to install your Dimmer
• Slotted/Philips Screwdriver
• Pliers
• Pencil
• Electrical Tape
• Ruler
• Cutters
Installing Dimmer by itself or with other devices
If installing Dimmer in a single device application, proceed
with the
INSTALLING YOUR DIMMER
section. If installing
Dimmer in a multi-device application, proceed as follows:
Your Dimmer includes three color options. The Dimmer
ships with the White frame attached. To change color of
frame, proceed as follows:
Changing the color of your Dimmer
Push in side at tab
to release
Line up tabs and
press in side to attach
Note:
Move slider on dimmer and slider on change kit
to bottom of the slide bar prior to engaging.
MULTI-DEVICE APPLICATION:
NOTE:
You only need to remove side sections if installing
with other dimmers or if it does not fit in wall box – not
when installing with mechanical switches.
When installing more than one dimmer in the same
location, the side sections of the mounting strap must be
removed. Use pliers to carefully bend side sections back
and forth until they break off.
Bend back and
forth to remove side section
Remove
all inner
side
sections
Do not
remove
outer
side
sections
WARNING:
TO AVOID FIRE, SHOCK, OR DEATH;
TURN
OFF POWER
at circuit breaker or fuse and test that power is
off before wiring!
Note:
No derating is required in this mult-device
installation as referenced in the following chart.
MAXIMUM BULB WATTAGE:
0-10VDC ballasts are rated in Volt-Amps (VA). The maximum
number of ballast per dimmer is based on the load VA rating.
The maximum bulb wattage is determined by the efficiency of
the ballast.
NOTE:
For additional switching capacity, use dimmers in
conjuction with a Leviton OPP20 120/277V Power Pack.
For applications using Leviton's OPP20 Power Pack
(Shown in Wiring Diagrams 2 & 4), the OPP20 switch
ratings are as follows (refer to OPP20 Instruction Sheet
for additional information):
OPP20 SWITCH RATINGS:
20 Amps for 120 and 277 VAC Ballast
0-10 VDC Sink Current Rating:
28 mA maximum sink current. Contact your ballast
manufacturer for the sink current consumption of the ballast.
INSTALLING YOUR DIMMER
Step 3A
Step 2
Preparing wires:
• Pull off pre-cut insulation from Dimmer leads.
• Make sure that the ends of the wires from the wall box are
straight
(cut if necessary).
• Remove 5/8" (1.6 cm) of insulation from each wire in the wall
box (shown).
•
For Single-Pole Application, go to Step 4A.
•
For 3-Way Application, go to Step 4B.
Strip Gage
5/8"
(1.6 cm)
Cut
(if necessary)
Strip 5/8"
(1.6 cm)
Insert wires straight
then twist clockwise
Electrical Tape
Neutral
Ground
Black
Red
Pink
Violet
Green
Red
This wire is used in 3-way installations only.
For single pole installations, do not remove this
insulating label.
Single-Pole Wiring Application:
•
Green dimmer Ground lead to Green or bare copper wire in
wall box.
•
Black dimmer lead to Line Hot wall box wire.
•
Red dimmer lead without insulating label to Load wall box wire.
•
Remaining Red dimmer lead should have Red insulation
label affixed.
NOTE:
If insulating label is not affixed to Red lead, use a small
wire nut or electrical tape to cap off.
•
Violet dimmer lead to (+) Violet connection on ballast.
•
Pink dimmer lead to (-) Pink or (-) Gray connection on ballast.
• Proceed to Step 4.
Connect wires per WIRING DIAGRAM 1
(shown on page 2) as follows:
Screw wire connectors on clockwise making sure no bare
conductors show below the wire connectors. Secure each
connector with electrical tape.
NOTE:
Ensure that low-voltage wiring (for Pink and Violet
connection of dimmer) is installed at wallbox that will house
the IP710 Dimmer.
Step 3B
Neutral
Ground
Black
Red
Pink
Violet
Green
Red
•
Green dimmer Ground lead to Green or bare copper wire in
wall box.
•
Black dimmer lead to tagged (common) wall box wire
identified in step 2.
•
Remove Red insulating label from Red lead.
•
First Traveler wall box wire identified in step 2 to any red
dimmer lead.
•
Second Traveler wall box wire identified in step 2 to the
remaining red dimmer lead.
•
Violet dimmer lead to (+) Violet connection on ballast.
•
Pink dimmer lead to (-) Pink or (-) Gray connection on
ballast.
• Proceed to Step 4.
3-Way Wiring Application:
Connect wires per WIRING DIAGRAM 3
(shown on page 2) as follows:
Screw wire connectors on clockwise making sure no bare
conductors show below the wire connectors. Secure each
connector with electrical tape.
NOTES:
• Dimmer can be installed on either the Load or Line side.
•
Ensure that low-voltage wiring (for Pink and Violet
connection of dimmer) is installed at wallbox that will
house the IP710 Dimmer.
•
For additional switching capacity, use dimmers in
conjuction with a Leviton OPP20 120/277V Power Pack.
Insert wires straight then
twist clockwise
Electrical Tape
NOTES:
•
Ensure that low-voltage wiring (for Pink and Violet
connection of dimmer) is installed at wallbox that will house
the IP710 Dimmer.
• For additional switching capacity, use dimmers in conjuction
with a Leviton OPP20 120/277V Power Pack.
Single Pole
1.
Line (Hot)
2.
Neutral
3.
Ground
4.
Load
5.
Pink (-) or Gray (-)
6.
Violet (+)
3-Way
1.
Load
(See note below)
2.
Neutral
3.
Ground
4.
First Traveler – note color
5.
Second Traveler – note color
6.
Pink (-) or Gray (-)
7.
Violet (+)
3
2
1
6
7
4
5
3
1
4
5
6
2
INSTALLATION INSTRUCTIONS
ENGLISH
MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE
Cat. No.
Volts
Single
Two Gang
More than
2 Devices
IP710-LF
120
1200VA
1200VA
1200VA
IP710-LF
277
1500VA
1500VA
1500VA
WEB
VERSION