manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Сервисное руководство Challenge 130TC-A-160000 доступно для бесплатного скачивания на manualshive.com. Получите подробное описание и инструкции по использованию этого товара, чтобы использовать его на полную мощность. Научитесь эффективно обслуживать и ремонтировать ваш продукт, следуя нашему руководству.

Поделиться
Скачать
background image

 

 

MAY 2019 

 

CMT-130TC Book Trimmer 

2-10

 

2. Status Indicator RAPs

 

RAP 2.4 Input Power 

This procedure is used to establish main, AC 
power to the machine. 

WARNING 

Improper connection of the grounding con-
ductor can result in the risk of electrical 
shock.  The following must be observed. 
 
Never attempt any maintenance function that 
is not specifically called out in the service 
procedures. 

WARNING 

HIGH VOLTAGE!  Use extreme caution when 
testing High voltage lines.  Serious injury or 
death may result from unsafe testing prac-
tices. 

CAUTION 

If the voltage measurements are not as specified 
in the following steps, the cause must be cor-
rected. 

Voltage Requirements 

 

200 to 240 VAC for 208/230 volts for 
60Hz machines 

 

360 to 420 VAC for 380/415 volts for 
50Hz machines 

 

Procedure 

1.  Switch the main power OFF using the 

red/yellow switch on the front of the trimmer. 

2.  Remove the electrical panel door located on 

the lower right side of the machine.  Check 

the line voltage by measuring the voltage 
between the AC lines (L1, L2, L3) at the 
power hookup (Figure 2-2).  The line voltage 
should meet the following specifications: 

 

200 to 240 VAC for 208/230 volts for 
60Hz machines 

 

360 to 420 VAC for 380/415 volts for 
50Hz machines 

3.  Does line voltage meet these conditions? 

Y  N 

Have a licensed electrician correct the line 
voltage. 

4.  Switch the main power ON. 

5.  Is there line voltage between M1 and M2 at 

the electrical panel (Figure 2-2)? 

Y  N 

Disconnect main power and replace the 
main power switch (PL 5.1 Main Assembly 
59000 (1/14)).  

6.  Is there line voltage between wires 1 and 2 

at the CB1 and CB2 circuit breakers (Figure 
2-2)? 

Y  N 

Reset circuit breakers CB1 and/or CB2 if 
tripped.  If a circuit breaker continues to trip, 
use applicable schematic to troubleshoot af-
fected circuit (Section 7, Wiring Data). 

7.  Remove the 

trimmer’s lower front panel. 

8.  Check proper connection of wires 1, 2, 20, 

and 22 to transformer T1 (Figure 2-3).  Is 
there 120 VAC between wires 20 and 22 at 
the transformer? 

Y  N 

Disconnect main power and replace trans-
former T1 (PL 5.1 Main Assembly 59000 
(1/14)). 

9.  Is there 120 VAC between wires 21 and 22 

at the electrical panel (Figure 2-2)? 

Y  N 

Reset circuit breaker CB3 if tripped.  If circuit 
breaker continues to trip, use applicable 
schematic to troubleshoot affected circuit 
(Section 7, Wiring Data). 

10.  Is there 120 VAC between wires 23 and 22 

at the electrical panel (Figure 2-2)? 

Y  N 

Reset circuit breaker CB4 if tripped.  If circuit 
breaker continues to trip, use applicable 
schematic to troubleshoot affected circuit 
(Section 7, Wiring Data). 

11.  Is there 120 VAC between wires 27 and 22 

at the electrical panel (Figure 2-2)? 

Y  N 

Reset circuit breaker CB5 if tripped.  If circuit 
breaker continues to trip, use applicable 
schematic to troubleshoot affected circuit 
(Section 7, Wiring Data). 

12.  Is there 120 VAC between wires 6 and 22 at 

the electrical panel (Figure 2-2)? 

Y  N 

Reset circuit breaker CB6 if tripped.  If circuit 
breaker continues to trip, use applicable 
schematic to troubleshoot affected circuit 
(Section 7, Wiring Data). 

13.  Is there 120 VAC between wires 24 and 25 

at EMI #2 filter (Figure 2-2)? 

Y  N 

Disconnect main power and replace the EMI 
filter (PL 5.16 Power Panel EE-3503 (1/2)). 

Input power is normal. 

 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Gardena EasyCut 400/25 Operating Instructions Manual preview
EasyCut 400/25
Бренд: Gardena Страницы: 15
Gardena ComfortCut 450/25 Operating Instructions Manual preview
ComfortCut 450/25
Бренд: Gardena Страницы: 16
Gardena EasyCut Li-18/23 R Operating Instructions Manual preview
EasyCut Li-18/23 R
Бренд: Gardena Страницы: 16
Gardena EasyCut Li-18/23 R Operator'S Manual preview
EasyCut Li-18/23 R
Бренд: Gardena Страницы: 11
Villager ET 555 Instruction Manual preview
ET 555
Бренд: Villager Страницы: 165
F&F FOX Wi-DIM1S1-P Instructions Manual preview
FOX Wi-DIM1S1-P
Бренд: F&F Страницы: 15
Tanaka THT series Owner'S Manual preview
THT series
Бренд: Tanaka Страницы: 21
Gardena 9833 Operator'S Manual preview
9833
Бренд: Gardena Страницы: 10
Weed Eater FL20 Instruction Manual preview
FL20
Бренд: Weed Eater Страницы: 36
Gardenline GLT 453 User Manual preview
GLT 453
Бренд: Gardenline Страницы: 16
XTline XT102875-2B2 User Manual preview
XT102875-2B2
Бренд: XTline Страницы: 31
Parkside 384536 2107 Translation Of The Original Instructions preview
384536 2107
Бренд: Parkside Страницы: 122
Parkside 385568 2107 Operation And Safety Notes Translation Of The Original Instructions preview
385568 2107
Бренд: Parkside Страницы: 157
Draper GT2222 Instructions Manual preview
GT2222
Бренд: Draper Страницы: 10
Draper GTP26 Instructions For preview
GTP26
Бренд: Draper Страницы: 16
Draper GT530B User Manual preview
GT530B
Бренд: Draper Страницы: 20
Draper HTC18LI Instructions Manual preview
HTC18LI
Бренд: Draper Страницы: 24
IKRA Mogatec Gartenmeister GM ART 4030 Operating Instructions Manual preview
Gartenmeister GM ART 4030
Бренд: IKRA Mogatec Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды