Challenge 130TC-A-160000 Скачать руководство пользователя страница 137

Страница: 137 / 282

MAY 2019

CMT-130TC Book Trimmer

4-31

4. Repair/Adjustment Procedures

REP 4.26 Accessory PWB Replace-
ment

The following procedure outlines the steps nec-
essary to replace an infeed/outfeed accessory
PWB.

CAUTION

Observe standard ESD protection procedures
while replacing any PWB's. Damage may result
due to static discharge.

Procedure

1. Switch the main power OFF and lockout

power to the trimmer.

WARNING

Disconnect and lockout power as described
in the Power Lockout Procedure on page ix.

2. Remove the door or panel that covers the

accessory’s electrical panel.

3. Disconnect all cable connectors from the

PWB.

4. Remove the five nuts that mount the PWB to

standoffs on the electrical panel (Figure
4-44).

5. Carefully remove the new PWB from the

electro-static bag that it was shipped in, and
place the old PWB in the empty bag.

6. Install the new PWB on the five standoffs on

the electrical panel, and attach it securely
with all five nuts.

7. Securely connect all cables to the new

PWB.

8. Reinstall the electrical panel door/cover.

9. Restore power to the trimmer and switch the

main power ON.

10. Run a few test books through the trimmer

and accessories to make sure everything is
working properly.

Figure 4-44. Stacker PWB

Содержание 130TC-A-160000



























































































































































































































































































Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Похожие инструкции для 130TC-A-160000

Бренды по названию

Популярные бренды

Challenge 130TC-A-160000, Руководство по обслуживанию

Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Похожие инструкции для 130TC-A-160000

Бренды по названию

Популярные бренды