manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 275

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

8-15 

8. Installation

 

Outfeed Option 2: 
Exit Conveyor 

 

Figure 8-35. Exit Conveyor 

Setup Procedure 

1.  Remove (4) sets of screws and washers 

from the right side of the trimmer, near and 
on the power panel cover.  Save them for 
later use. 

2.  Adjust the leveling feet of the Exit Conveyor 

such that the conveyor surface is approxi-
mately 33-7/8" (86.0 cm) from the floor and 
level, as shown in Figure 8-36.  

 

 

Figure 8-36. Exit Conveyor Height 

3.  Move the Exit Conveyor to the right-hand 

side of the trimmer such that the slots in the 
conveyor mounting brackets line up with the 
holes in the side of the trimmer. 

4.  Fasten the conveyor to the trimmer using 

the hardware from step 1. 

Cable and Air Tubing Connections

 

1.  Remove the lower front panel of the trimmer 

and locate the yellow power cable coiled up 
inside the trimmer that is labelled with the 
number that corresponds to the label on the 
exit conveyor near the input connectors.  
The power cables are the larger diameter 
cables with 7-pin connectors on the end.   

2.  Route the power cable under the electrical 

enclosure and out of the right side of the 
trimmer. 

3.  Connect the power cable as shown in Figure 

8-37. 

 

Figure 8-37. Power Cable Connection 

4.  Now locate the yellow communication cable 

that is labelled with the number that corre-
sponds to the label on the exit conveyor 
near the input connectors.  It is a small di-
ameter cable with a 3-pin connector on the 
end. The cable will come from either the ele-
vator or pile feeder (if equipped), otherwise 
from inside the trimmer. 

5.  Connect the communication cable as shown 

in Figure 8-38. 

 

 

Figure 8-38. Comm. Cable Connections 

Now go to Section 8.7 Main Power Hookup to 
continue the setup process.

 

 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды