Challenge 130TC-A-160000 Скачать руководство пользователя страница 77

Страница: 77 / 282

MAY 2019

CMT-130TC Book Trimmer

2-65

2. Status Indicator RAPs

RAP 2.57 Book In From Binder Sen-
sor

Elevator I/O PWB Input 2

The book in from binder sensor detects books
entering the Tilt Infeed Conveyor. This sensor
also wakes the trimmer from sleep mode when
triggered.

Possible Fault Indicators



The machine never enters sleep mode.



Books accumulate in the tilt infeed con-
veyor.



The machine does not return to ready
mode.

Initial Actions

Check that all cables between the trimmer, Ele-
vator, and Tilt Infeed Conveyor are securely fas-
tened and are not damaged.

Check for loose or damaged wires 42, 73, and
74 at the Elevator electrical panel (Figure 2-86).

Procedure

1. Switch the main power ON and go to the El-

evator diagnostic screen (GP 6.2 Input/Out-
put Diagnostics). Make sure that the sensor
is not obstructed.

Is input “Book In From

Binder” off?

Y N

Disconnect wire 42 from the Elevator I/O
PWB (Figure 2-86). Does the input switch
off?

Y N

Disconnect power and replace the Ele-
vator I/O PWB (REP 4.26 Accessory
PWB Replacement).

Adjust the sensor (GP 6.7 Diffuse Sensors)
and replace if faulty (PL 5.47 Tilt Conv. Elec.
Panel EE-3547).

2. Short wire 42 to wire 74. Does the input

switch on?

Y N

Disconnect power and replace the Elevator
I/O PWB (REP 4.26 Accessory PWB Re-
placement).

3. Adjust the sensor (GP 6.7 Diffuse Sensors)

and replace if faulty (PL 5.47 Tilt Conv. Elec.
Panel EE-3547).

Figure 2-85. Book In From Binder Sensor

Figure 2-86. Elevator Electrical Panel

Содержание 130TC-A-160000



























































































































































































































































































Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Бренды по названию

Популярные бренды

Challenge 130TC-A-160000, Руководство по обслуживанию

Результаты поиска

Содержание 130TC-A-160000

Отзывы:

Бренды по названию

Популярные бренды