Challenge 130TC-A-160000 Скачать руководство пользователя страница 234 | Manualshive

Страница: 234 / 282

background image

MAY 2019

6. General Procedures/Information

6-20

CMT-130TC Book Trimmer

GP 6.17 Book Size Chart

The physical parts of a book are defined as fol-
lows and will be referenced as such throughout
this manual. Book dimensions are referenced
as

“spine length” x “top (or bottom) edge length”.

Spine:

The edge of a book where the pages

are bound together.

Top edge:

Also known as the head, the top

edge is the edge of the book that is facing away
from the reader.

Bottom edge:

Also known as the foot, the bot-

tom edge is the edge of the book that is facing
toward the reader.

Face:

The face or fore-edge is the edge of the

book from which it is opened.

Book block:

A book block is the printed and

collated pages of a book that does not include
the cover. It contains all front and end matter as
well as the text block.

Untrimmed book:

An untrimmed book is a

book block that has been bound with a cover but
has not yet been trimmed to finish size.

Trimmed book:

A trimmed book has been

bound and trimmed to a finish size.

The charts on Figure 6-19 can be used to deter-
mine if a specific book layout can be trimmed by
the CMT-130TC. Using the trimmed spine
height (h) and the bottom trim (x), make sure the
desired book size falls within the shaded region
of the chart. The overall untrimmed and
trimmed book dimensions must also be less
than the maximum allowed (See GP 6.16 Speci-
fications).

The CMT-130TC software will not allow a book
to be trimmed outside this range. The operator
should be aware of these size constraints before
books are printed.

Figure 6-19. Book Size Charts

«
...
232
233
234
235
236
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: LAAWA Страницы: 14

Бренд: MADER GARDEN Страницы: 26

Бренд: Shindaiwa Страницы: 164

Бренд: Zombi Страницы: 30

Бренд: Qualcast Страницы: 12

Бренд: Yard Machines Страницы: 16

Бренд: Morrison Страницы: 8

Бренд: Texas Equipment Страницы: 20

Бренд: GreenWorks Страницы: 20

Бренд: Ozito Страницы: 7

Бренд: Parkside Страницы: 122

Бренд: Clas Ohlson Страницы: 64

Бренд: Clas Ohlson Страницы: 104

BlueRazor MST601

Бренд: Blaupunkt Страницы: 56

Бренд: Leviton Страницы: 2

vizia rf + VRMX1-1L

Бренд: Leviton Страницы: 10

decora smart DZ1KD

Бренд: Leviton Страницы: 3

Бренд: Leviton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды