Challenge 130TC-A-160000 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 282

background image

MAY 2019

2. Status Indicator RAPs

2-42

CMT-130TC Book Trimmer

RAP 2.34 Registration Assembly Mo-
tor

The registration assembly is located on the table
just past the right-hand conveyor. It is used to
register books in the proper location relative to
the gripper.

Possible Fault Indicators



The registration assembly fails to move
when it should (after pressing green
start button).



“Registration Position Error”

or

“Registration Data Error”

oc-

curs repeatedly.

Initial Actions

Visually inspect all circuit breaker switches to
see if any are tripped or turned off.

Procedure

1. Switch the main power OFF. Turn the regis-

tration assembly drive motor manually by
turning the drive pulley. Does the registra-
tion plate move freely?

Y N

Disconnect power and replace the registra-
tion assembly (PL 5.9 Main Assembly 59000
(9/14)).

2. Switch the main power ON, and press the

green start button to initialize.

3. Check voltage between wires 5 and 22 at

EMI #1 on the electrical panel (Figure 2-54).
Is there 120 VAC?

Y N

Go to RAP 2.4 Input Power.

4. Check voltage between wires 14 and 16 at

EMI #1 on the electrical panel (Figure 2-54).
Is there 120 VAC?

Y N

Disconnect main power and replace the EMI
filter #1 (PL 5.16 Power Panel EE-3503
(1/2))

5. Is there 5 VDC between wires 7 and 8 at the

encoder cable connector?

Y N

Check for loose or damaged wires 7 and 8.

6. Is there 5 VDC between wires 7 and 8 at the

main PWB?

Y N

Go to RAP 2.5 DC Power and check the 5
VDC circuit.

7. Does the voltage between wires 8 and 9 and

also wires 8 and 10 at the encoder cable
connector change between 0 and 5 VDC
while the encoder is turned manually?

Y N

Disconnect power and replace the encoder
(PL 5.15 Registration Asm. 56311-3).

8. Go to the diagnostic screen and enable out-

puts (GP 6.2 Input/Output Diagnostics).
Make sure all doors are closed, then acti-
vate the Interlock Relay output. Press the
green start button to energize the IR relay.
The “Interlock Relay IR” input should switch
on.

9. In the diagnostic screen, have someone

press the “Sideguide Test” button. This will
initiate movement of the registration.

10. Is there nominal motor voltage (65-75 VDC

in fast speed, and 10-20 VDC in slow speed
– actual voltage may vary) between wires 30
and 31 while the registration is moving?

Y N

Disconnect power and replace the main
PWB (REP 4.23 Main PWB Replacement).

11. Disconnect power and replace the motor (PL

5.15 Registration Asm. 56311-3).

Figure 2-53. Registration Assembly Motor

Figure 2-54. EMI #1

«
...
52
53
54
55
56
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Shindaiwa Страницы: 164

Бренд: Yard Machines Страницы: 54

Бренд: Remington Страницы: 44

Craftsman 536.796526

Бренд: Sears Страницы: 16

CRAFTSMAN 316.791810

Бренд: Sears Страницы: 40

Бренд: HART Страницы: 38

Бренд: Powermate Страницы: 69

Бренд: Draper Страницы: 22

Бренд: McCulloch Страницы: 1

MULTITRIM CT250X

Бренд: Flymo Страницы: 95

Бренд: Yard-Man Страницы: 92

Бренд: EarthWise Страницы: 30

Бренд: Zenoah Страницы: 24

PowerPlus POWDPG7545

Бренд: VARO Страницы: 12

Бренд: Tanaka Страницы: 17

Бренд: Gardena Страницы: 14

Бренд: Fellowes Страницы: 58

Бренд: Echo Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды