Challenge 130TC-A-160000 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 282

background image

MAY 2019

2. Status Indicator RAPs

2-18

CMT-130TC Book Trimmer

RAP 2.10 Door Interlocks

– Trimmer

Inputs 8, 11, and 29

Door interlock switches are located on each of
the

trimmer’s three doors: front, side, and rear

Possible Fault Indicators



A “door open” message is displayed
while all doors are closed.



A door is open, but the machine contin-
ues to operate.



A door is open, but no message is dis-
played on the screen.

Initial Actions

Check that all three doors are securely closed.
Check and repair loose wires 83A, 102, 103,
104 at the electrical panel. Check and repair
loose wires on all 3 door interlock switches.

Procedure (does not operate with doors
closed)

1. Does the

screen show a “door open” mes-

sage?

Y N

Cycle power OFF and then back ON. Then
go to the diagnostic screen (GP 6.2 In-
put/Output Diagnostics). Open each door. Is
a tone heard with each opening?

Y N

Perform RAP 2.11 Interlock Test. If this
does not fix the problem, disconnect
power and replace the main PWB (REP
4.23 Main PWB Replacement).

Disconnect power and replace the Open
Door Indicator PWB (Figure 2-10).

2. Check the operation of the indicated inter-

lock switch and make sure that the actuator

key engages fully into the switch body when
the door is closed, and pulls out of the
switch body when the door is opened. Ad-
just if necessary (GP 6.11 Keyed Interlock
Switches). Did this fix the problem?

Y N

Perform RAP 2.11 Interlock Test and re-
place any defective switches.

Repair complete.

Procedure (operates with a door open)

WARNING

Do not operate the machine until this switch
is replaced and functioning properly. Failure
to do so could allow the machine to operate
in an un-safe state. Serious injury or death
may result.

1. Check the operation of the applicable inter-

lock switch and make sure that the actuator
key engages fully into the switch body when
the door is closed, and pulls out of the
switch body when the door is opened. Ad-
just if necessary (GP 6.11 Keyed Interlock
Switches). Did this fix the problem?

Y N

Perform RAP 2.11 Interlock Test and re-
place any defective switches.

Repair complete.

Figure 2-9. Door Interlocks

Figure 2-10. Open Door Indicator PWB

«
...
28
29
30
31
32
...
»

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 130TC-A-160000

Бренд: Yard Machines Страницы: 52

Бренд: Weed Eater Страницы: 12

classicCut special

Бренд: Gardena Страницы: 13

Бренд: Black Max Страницы: 36

Бренд: QGarden Страницы: 24

EXTREME GRIP PRO

Бренд: Wahl Страницы: 2

Бренд: Poulan Pro Страницы: 21

Бренд: AEG Страницы: 28

Бренд: AEG Страницы: 24

Atlas Copco HS 40

Бренд: AEG Страницы: 68

Бренд: Craftsman Страницы: 26

Бренд: Craftsman Страницы: 21

79441 - 20 in. Hedge Trimmer

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 10

Бренд: Craftsman Страницы: 14

Бренд: Craftsman Страницы: 19

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды