manualshive.com logo in svg

Challenge 130TC-A-160000, Руководство по обслуживанию

Поделиться
Скачать
Challenge 130TC-A-160000 Скачать руководство пользователя страница 220

 

 

 

MAY 2019 

 

6. General Procedures/Information

 

6-6 

CMT-130TC Book Trimmer 

GP 6.5 Proximity Sensors 

This procedure describes how to properly adjust 
the metal-sensing proximity sensors located in 
the CMT-130TC and its accessory equipment. 

A metal-sensing proximity sensor is actuated 
when a metal object gets close enough to the 
sensor to change the magnetic field in front of 
the sensing surface.  All metal-sensing proximity 
sensors in the CMT-130TC must be adjusted to 
within 0.030" (0.75 mm) of their actuators. 

There are two types of metal-sensing proximity 
sensors used in the trimmer and accessories: 
rectangular and cylindrical (Figure 6-7). 

Procedure 

1.  Switch the main power OFF. 

2.  Clean any debris from the actuator and sen-

sor. 

3.  Inspect the sensor for physical damage.  

Replace the sensor if the housing or body is 
cracked. 

4.  Loosen the mounting hardware and un-

mount the sensor.  Rectangular proximities 
are mounted on adjustable brackets.  Cylin-
drical proximities are mounted through holes 
and held in place with two nuts. 

5.  Switch the main power ON 

and click the “Di-

agnostic” button to bring up the diagnostic 
screen.  If applicable, click on an accessory 
diagnostic button to bring up a specific ac-
cessory’s diagnostic screen. 

6.  Actuate the sensor by placing a metal (steel) 

object within 0.030" (0.75 mm) of the sens-
ing surface.  If the sensor and main PWB 
are working correctly, the LED on the sensor 
will change state, and an audible tone will be 
emitted from the main PWB.  Does the sen-
sor change state when actuated? 

Y  N 

Perform the RAP associated with the spe-
cific sensor.   

7.  Mount the sensor such that the actuator 

comes within 0.030" (0.75 mm) of the sens-
ing surface during normal operation.  It is 
best to have the actuator come as close as 
possible to the sensor without touching it.  It 
may be helpful (where possible) to also ad-
just the actuator in order to accomplish 
proper spacing. 

8.  Tighten all mounting hardware. 

 

 

Figure 6-7. Metal-Sensing Proximity Sen-

sores 

 

Содержание 130TC-A-160000



























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды