Canon iR7086, Руководство по обслуживанию

Страница: 663 / 735

Chapter 17
17-75
ATCT-ADD
*** Auto clear time additional SW
1
This function is to set the auto clear time(or auto-offline transfer time that correspounds with auto clear time) to less than 1 min.
Auto clear time additional SW
This function allows to set the auto clear time to 10sec, 20sec, 30sec, 40sec, 50sec.
(Conventionally, 1 to 9 min)
This function is to set the auto clear time(or auto-offline transfer time that correspounds with auto clear time) to less than 1 min.
Setting range
0: Without addition
1: With addition (10sec, 20sec, 30sec, 40sec, 50sec additions)
Remarks
When this SW is activated, there is no message of [Numeric key is also available for entering (0min=none/1 to 9 min)] at the auto clear
setting screen in user mode.
HDCR-DSW
*** Selection of whether to display 'all HDD data clear ON/OFF' item in user mode
1
To select whether to display the 'all HDD data clear ON/OFF' item in the user mode.
This mode takes effect only when the all HDD data clear function (licensed) is activated.
When the user asks for the item to be provided.
0: The item is not displayed.[default]
1: The item is displayed.
PB-MAX-N
*** Not for use
1
PB-MAX-T
*** Not for use
1
SIZE-DET Use it to enable/disable the original size detection function.
2
The machine is designed so that the scanning lamp goes on for detection of the size of the original when the copyboard cover is opened
and then closed; if the user finds its light to be too intense, set it to '0'.
settings
0: off; 1: on (default)
DATE-DSP Use it to switch between date notations.
2
settings
0: YYMM/DD; 1: DD/MM/YY; 2: MM/DD/YY
MB-CCV Use it to set restrictions on the individuals permitted the use of mail box control card.
2
settings
0: do not restrict (default); 1: restrict
PR-D-SEL Use it to set the density for printing (PDL input).
2
settings
0: (light) <->4 (standard; default) <-> 8 (dark)
TRY-STP Use it to set the output interrupt mode used in response to a tray full condition.
2
settings
0: normal mode (suspend when finisher tray becomes full; default); 1: suspend in relation to height
MF-LG-ST Use it to set extra length mode key.
2
settings
0: normal (default); 1: indicate extra length key on supported mode screen
SPECK-DP Use it to enable/disable display of a warning message in response to the result of dust detection for stream reading.
2
settings
0: do not indicate; 1: indicate (default)
CNT-DISP Use it to enable/disable the indication of a serial number in response to a press on the counter check mode.
2
settings
0: indicate (default); 1: do not indicate
PH-D-SEL Use it to specify the number of lines for photo mode copy.
2
settings
0: 141 lines (default); 1: 134 lines
If setting '1', the degree of half-tone unevenness decreases despite of lower resolution.
MEMO:
-Effective only at copying (ineffective at printing)
-This item is not used at normal servicing.
OP-SZ-DT Use it to enable/disable the original size detection function in reference to the opening of the copyboard cover.
2
The machine may be set so that it detects the size of an original with the copyboard cover open (e.g., for a book).
settings
0: off (default); 1: on
If set to '1', the machine executes original size detection in response to a press on the Start key.
NW-SCAN Use it to enable/disable the network scan function.
2
settings
0: do not permit; 1: permit
This choice is not available on a Japanese model. For a non-Japanese PS/PCL model, the settings is fixed to '1'.
COPIER > OPTION > USER
*: model equipped with DADF-Q1 (outside Japan: iR7105/7095; inside Japan: All model).
**: model equipped with DADF-M1 (outside Japan: iR7086).
***: up graded version
Sub item Description Level