Canon iR7086, Руководство по обслуживанию

Страница: 517 / 735

Chapter 14
14-17
- Print out the user mode/service mode data.
- If you are replacing the main controller PCB, be sure to physically transfer
the following from the existing to the new PCB:
[1] BootROM
[2] HDD
[3] image memory (DDR-SDRAM)
[4] counter memory PCB
F-14-33
MEMO: Image memory (DDR-SDRAM)
The machine is equipped with the following image memory:
capacity: 1 GB
quantity: 1 pc.
Use one of the 2 slots. There is no optional memory for expansion.
1) Turn on the power. If there is a backup of the SRAM data (i.e., if down-
loaded using the SST), upload it.
2) Execute the following service mode item:
COPIER > FUNCTION > CLEAR > CA-KEY (Level 2)
3) Turn off and then on the power.
MEMO:
Execution of the following may delete the keys/certificates used for encrypt-
ed communications and the CA certificates used for authentication of exter-
nal server certificates:
- replacement/formatting of the HDD
- replacement of the main controller PCB/initialization of the RAM
If a key/certificate for encrypted communications has been deleted, the con-
trol panel screen will indicate a message to the effect that the key has been
corrupted: however, the key/certificate/CA certificate installed at time of
shipment from the factory may be
brought back by executing the following: COPIER>FUNC-
TION>CLEAR>CA-KEY. If doing so has failed, use the SST to install the
key/certificate/CA certificate, and execute CA-KEY once again.
Points to Note When Executing Service Mode Item CA-KEY
If the user has generated/added a key/certificate/CA certificate on his/her
own, executing CA-KEY will also delete these files. Inform the user of this,
and ask him/her to re-install them as necessary after the execution of CA-
KEY.
Points to Note When Fitting the Security Expansion Board
Whenever possible, do not replace the main controller PCB as part of the
troubleshooting work conducted in relation to the installation of the security
expansion board (option).
The machine checks the compatibility between the HDD and the main con-
troller PCB when a security expansion board is installed. Replacement with
a new board will cause the formatting of the HDD to start automatically, thus
deleting all user data.
T-14-4
*1: limited to those settings that may be exported using a remote UI or trans-
mitted as part of machine information.
*2: limited to when the MEAP application in question offers a backup func-
tion.
*3: limited to data within the User Box.
When Replacing the Main Controller PCB
- Explain to the user that all user data will be deleted.
- As necessary, ask the user to make a backup of those data items that permit
making of a backup.
- Explain to the user that the following data items do not permit making of a
backup, and require remedial action:
<Suggestions for Remedial Action>
- for mode settings stored using the copy/Box function, ask the user to newly
enter the settings.
- for read mode settings stored using the transmission function, ask the user
to newly enter the settings.
- for files that are yet to be transmitted (i.e., files for selected timer transmis-
sion or reserved for transmission), ask the user to newly transmit them.
- for registered forms used in image synthesis, ask the user to newly enter
them.
- for MEAP applications, ask the user to newly install them.
- for MEAP SMS (service management services) passwords, access the fol-
lowing: http://<iR IP address>:8000/SMS. (Use the factory password
"MeapSmsLogin" (case-sensitive) to log in and change the password.
- for job histories, if a record is needed, ask the user to store away the history
using a remote UI. (However, there is no way of
returning the history to the HDD.)
- for key pairs and server certificates, if the user has added any, ask for re-
installation.
14.7.3 After Replacing the DC Controller PCB
0010-9329
iR7105 / iR7095 / iR7086
Before starting the work and checking
- Be sure to print out the user mode/service mode data before replacing the
DC controller PCB.
- Be sure to adjust the on/off timing of the clutch in service mode (COPIER
> FUNCTION > MISC-P > CL-ADJ) after replacing the DC controller
PCB. Before adjusting, be sure to place two or more sheets of A4 or LTR
in the following pick-up slots, otherwise you can't perform the adjust-
ment.
- Left deck
- Cassette 4
- Paper deck (accessory)
Points to note when turning the power off (Executing the shutdown
sequence)
Be sure to turn off the main power after executing the shutdown sequence to
protect the hard disk.
Points to note when turning the power on (When Delivery accessory
is mounted)
When any delivery accessory (Finisher, Stacker, and/or Perfect binder) is
Data item deleted Backup
possibility
address data registered in the address book Yes
settings made in user mode Yes *1
settings stored in memory Yes
license file for MEAP application Yes
user authentication information stored using SDL
(simple device login) Yes
[1]
[2]
[3]
[4]
data stored using MEAP application Yes *2
mode memory stored using copy function or Box
function No
data in Box Yes *3
read mode settings stored using transmission function No
files yet to be read (those selected for timer
transmission or reserved for transmission) No
forms stored for image synthesis No
MEAP application No
password for MEAP SMS (service management
services); returns to factory default No
job history information No
user authentication information stored in relation to
SSO (local device authentication) Yes
key pairs and server certificates stored in conjunction
with system control settings No
Data item deleted Backup
possibility