Canon IMAGERUNNER ADVANCE C5030, Руководство по обслуживанию, Страница: 912 / 1455

8
8
8-212
8-212
Service Mode > COPIER > OPTION > USER
Service Mode > COPIER > OPTION > USER
COPIER > OPTION > USER
SND-RATE Set compress ratio at SEND high compress
Lv.2 Details To set the compression ratio when the data compression ratio for
SEND (transmission) is set to “Compact”.
As the value is larger, the compression ratio is higher (the file size
becomes small).
Use case When making the transmission file size smaller
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution As the value is too large, an image is deteriorated.
Display/adj/set range 0 to 2
0: Compression ratio 1/16, 1: Compression ratio 1/20, 2:
Compression ratio 1/24
Default value 0
CTM-S06 Set of password delete from export file
Lv.2 Details To set whether to delete password for file transmission address from
export file.
When 1 is set, the password of file transmission target is deleted at
the time of exporting address book data from remote UI.
Use case - Upon user’s request
- When preventing information leak
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Retained, 1: Deleted
Default value 1
FREG-SW Dspl/hide of MEAP counter free rgst area
Lv.2 Details To set whether to display or hide the free register area of MEAP
counter for SEND.
Use case At problem analysis
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution - Do not use this at the normal service.
- Take necessary action in accordance with the instructions from the
Quality Support Division.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
COPIER > OPTION > USER
IFAX-SZL Setting of IFAX send size limit
Lv.2 Details To set for restricting data size at the time of IFAX transmission that
does not go through the server.
With the setting to restrict the data size, it is to be #830 error in the
case of sending data that exceeds the upper limit value.
In the case that the data goes through the server, the size of
transmission data is always restricted.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Limited, 1: Unlimited (Restriction applies when data goes through
the server.)
Default value 1
IFAX-PGD Set page split TX at IFax Simple mode TX
Lv.2 Details To set whether to allow split-data transmission on a page basis in the
case that the transmission size in I-Fax Simple mode exceeds the
upper limit value.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution In the case to enable split-data transmission, be sure to receive
approval from the user in advance by explaining the following:
- No guarantee for page order on the reception side
- There is a possibility of interruption of other received jobs between
pages.
Display/adj/set range 0 to1
0: Disabled, 1: Enabled
Default value 0
MEAPSAFE Setting of MEAP safe mode
Lv.2 Details To set safe mode for MEAP platform.
MPSF is displayed on the Control Panel in safe mode.
In safe mode, MEAP application is stopped while just the system
application, which starts with initial state, is activated. This mode
enables obtaining log for cause analysis of MEAP failure.
Use case Perform system recovery processing when MEAP platform fails to
be activated due to resource conflict between MEAP applications,
service registration or use order.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal mode, 1: Safe mode
Default value 0