Canon IMAGERUNNER ADVANCE C5030, Руководство по обслуживанию, Страница: 864 / 1455

8
8
8-164
8-164
Service Mode > COPIER > OPTION > FNC-SW
Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
SVMD-ENT Setting of entry method to service mode
Lv.2 Details To set the way to get in service mode to prevent information leak.
Use case As needed
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Factory default
1: [Settings/Registration] - Pressing [4] and [9] at the same time -
[Settings/Registration]
Default value 0
FXWRNLVL Set Fix Film life display threshold VL
Lv.2 Details To set the threshold value to display the life of Fixing Film.
When COPIER> OPTION> DSPLY-SW> FXMSG-SW (ON/OFF of
Fixing Assembly replacement message) is 1 (default: 0), this setting
is enabled.
The counter for life judgment is stored in the DC Controller. The
counter value cannot be changed and checked.
Use case It is to prevent the occurrence of fixing failure in the case of
continuing to use the Fixing Film beyond its life.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
0: Warning is hidden.
1: Warning is displayed when the counter for life judgment reaches
the specified value.
2 and 3: Not used
Default value 0
Related service mode COPIER> OPTION> DSPLY-SW> FXMSG-SW
BASE-SW Model switch set from MEAP-Full to Base
Lv.1 Details To switch from the MEAP-Full model to the Base model.
Switch this mode in the case of restricting the operation of MEAP
application for trouble analysis.
Use case When trouble that caused by MEAP application occurs
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Switch from the Base model to the MEAP-Full model is not available.
Display/adj/set range 0 to 1
0: OFF (Base model), 1: ON (Full model)
Default value Depending on the setting of option bit (MeapModelBIT).
CKT-LANG [Not used]
COPIER > OPTION > FNC-SW
KSIZE-SW Set of Chinese paper (K-size) support
Lv.2 Details To set to detect/display the Chinese paper (K size paper: 8K, 16K).
Use case When using K-size paper
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Go through the following: COPIER > OPTION > FNC-SW > MODEL-
SZ; and if MODEL-SZ is “0: AB configuration”, this mode is enabled.
Display/adj/set range 0 to 1
0: Not supported, 1: Supported
Default value 0
Related service mode COPIER> OPTION> FNC-SW> MODEL-SZ
ORG-A4R Special paper size set in DADF mode: A4R
Lv.2 Details To set the size of special paper (A4R) that cannot be recognized in
DADF stream reading mode.
When picking up A4R size original from the DADF of the Inch/AB
configuration models, the size is converted into the specified size so
that an image can be formed properly.
Use case - Upon user’s request
- When picking up special paper size original from DADF
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: A4R, 1: FOLIO-R
Default value 0
PDF-RDCT PDF reduction set at forwarding
Lv.2 Details To set whether to reduce the image for transmission when converting
the image received by IFAX into PDF for e-mail/file transmission.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: With the current setting, 1: Image reduction
Default value 0