Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 300

Страница: 300 / 422

9.5

KNK03, KMV03, KLC03

9.5.1

Arranging the devices

Mount the KMV supply unit to the left of the KNK mains filter. The connection

points at KMV then can be accessed and wired more easily.

9.5.2

Mounting

Notes on mounting

To allow trouble-free servicing, make sure that the following aspects are

fulfilled after KSM has been mounted:
●

Connection points are easily accessible

●

Address selector switches are easily accessible

●

Diagnostic LED is visible

Preferably mount the device to a conductive surface. If this is

impossible, later on connect the second connection point of equipment

grounding conductor at the device to the equipment grounding system

of the installation.

For devices of the "W" and "A" cooling types, only the mounting position

G1 is allowed.

For the dimensions of the mounting holes, see the dimensional drawing

of the device.

Data of the mounting screws:
Devices of "B" or "I" cooling type:
●

Thread: M5

●

Tightening torque: 6 Nm

Devices of "A" or "W" cooling type:
●

Thread: M6

●

Tightening torque: 6 Nm

Cold plate

Devices of cooling type "B" are mounted on a cold plate.
Required cold plate properties:
See

chapter 9.1.3 "Cold plate" on page 279

9.6

Electrical connection

9.6.1

General information

High electrical voltage! Danger to life by

electric shock!

WARNING

Working within the range of live parts is extremely dangerous. Therefore:
●

Any work required on the electric system may be carried out only by

skilled electricians. It is absolutely necessary to use power tools.

●

Before starting work, the system must be de-energized and the power

switch be secured against unintentional or unauthorized re-energization.

●

Before starting work, the appropriate measuring equipment must be

used to check whether parts of the system are still under residual

voltage (e.g. caused by capacitors, etc.). Wait to allow the system to

discharge.

286/407

Mounting and installation

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды