Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 52

Страница: 52 / 422

3.2.3

Hazards by improper use

●

High electrical voltage and high working current! Danger to life or

serious injury by electric shock!

●

High electrical voltage by incorrect connection! Danger to life or injury by

electric shock!

●

Dangerous movements! Danger to life, serious injury or property

damage by unintended motor movements!

●

Health hazard for persons with heart pacemakers, metal implants and

hearing aids in proximity to electric drive systems!

●

Risk of burns by hot housing surfaces!

●

Risk of injury by improper handling! Injury by crushing, shearing, cutting,

hitting!

●

Risk of injury by improper handling of batteries!

●

Risk of injury by improper handling of pressurized lines!

3.3

Instructions with regard to specific dangers

3.3.1

Protection against contact with electrical parts and housings

This section concerns components of the electric drive and

control system with voltages of more than 50 volts.

Contact with parts conducting voltages above 50 volts can cause personal

danger and electric shock. When operating components of the electric drive

and control system, it is unavoidable that some parts of these components

conduct dangerous voltage.

High electrical voltage! Danger to life, risk of injury by electric shock or

serious injury!
●

Only qualified persons are allowed to operate, maintain and/or repair the

components of the electric drive and control system.

●

Follow the general installation and safety regulations when working on

power installations.

●

Before switching on, the equipment grounding conductor must have

been permanently connected to all electric components in accordance

with the connection diagram.

●

Even for brief measurements or tests, operation is only allowed if the

equipment grounding conductor has been permanently connected to the

points of the components provided for this purpose.

●

Before accessing electrical parts with voltage potentials higher than

50 V, you must disconnect electric components from the mains or from

the power supply unit. Secure the electric component from

reconnection.

●

With electric components, observe the following aspects:
Always wait 30 minutes after switching off power to allow live capacitors

to discharge before accessing an electric component. Measure the

electrical voltage of live parts before beginning to work to make sure

that the equipment is safe to touch.

38/407

Safety instructions for electric drives and controls

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды