Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 368

Страница: 368 / 422

POWERLINK

LED: Color / flashing pattern

Significance

Off

OFF
INITIALISATION
NOT_ACTIVE
No error

Flickering green

BASIC_ETHERNET

Green, lighting up once

PRE_OPERATIONAL_1

Green, lighting up twice

PRE_OPERATIONAL_2

Green, lighting up three times

READY_TO_OPERATE

Permanently lit green

OPERATIONAL

Flashing green

STOPPED

Permanently lit red

State machine error

One square corresponds to a duration of 50 ms

One square corresponds to a duration of 200 ms

Tab. 11-10:

Diagnostic LED

11.3.4

Diagnostic messages via parameters

The usual diagnostic parameters are used:
●

S-0-0095

●

S-0-0390

●

P-0-0009

●

…

See also parameter description of firmware.

11.3.5

Firmware functions

Easy startup mode

The easy startup mode is intended for initial commissioning. Easy startup can

be carried out with the "Rexroth IndraWorks D" commissioning software.
For easy startup, the digital inputs have been preset as follows:
●

E1 (X37.4): +24 V to activate positive direction of rotation

●

E2 (X37.2): +24 V to activate negative direction of rotation

354/407

Commissioning, operation, diagnostics and maintenance

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды