Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 21

Страница: 21 / 422

1.2

IndraDrive Mi drive system

1.2.1

Components

KCU02 drive connection box

The KCU02 drive connection box
●

supplies the KSM motor-integrated servo drives and the KMS near

motor servo drives
–

with power (from the DC bus connection to an HMV supply unit or

HCS converter)

–

with 42V control voltage

●

with integrated fuses protects the RKH hybrid cable against electric

overload

●

allows the higher-level control unit to communicate with the KSM motor-

integrated servo drives and KMS near motor servo drives

⇒

chapter "KSM02 motor-integrated servo drive" on page 2

⇒

chapter "KMS02 near motor servo drive" on page 3

KMV03 supply unit

The KMV03 supply unit
●

supplies the KSM motor-integrated servo drives and KMS near motor

servo drives
–

with power

–

with 42V control voltage

●

allows the higher-level control unit to communicate with the KSM motor-

integrated servo drives and KMS near motor servo drives

⇒

chapter "KNK03 mains filter, KMV03 supply unit, KLC03 DC bus capacitor

unit, KMS03 near motor servo drive" on page 4

KNK03 mains filter

Mains filters reduce radio interference and mains pollution.
⇒

chapter "KNK03 mains filter, KMV03 supply unit, KLC03 DC bus capacitor

unit, KMS03 near motor servo drive" on page 4

KLC03 DC bus capacitor unit

DC bus capacitor units buffer energy in the DC bus of the drive system.
⇒

chapter "KNK03 mains filter, KMV03 supply unit, KLC03 DC bus capacitor

unit, KMS03 near motor servo drive" on page 4

KSM motor-integrated servo drive

The KSM motor-integrated servo drive consists of:
●

Servo motor (on the basis of Rexroth IndraDyn S)

●

Drive electronics, consisting of control section and power section

⇒

chapter "KSM02 motor-integrated servo drive" on page 2

KMS near motor servo drive

The KMS near motor servo drive consists of control section and power

section.
⇒

chapter "KMS02 near motor servo drive" on page 3

RKH hybrid cable

The RKH hybrid cable replaces the following individual cables:

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

7/407

System presentation

R911335703_Edition 04 Bosch Rexroth AG

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды