Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 375

Страница: 375 / 422

11.5

Maintenance

11.5.1

Maintenance of the Motor Component

General Information

The motors operate in a maintenance-free way within the given operating

conditions and service life. However, operation under unfavorable conditions

can lead to limitations in availability.
●

Increase the availability with regular preventive maintenance measures.

Observe the information in the maintenance schedule of the machine

manufacturer and the maintenance measures described below.

Risk of burns by hot surfaces with

temperatures of more than 100 °C!

CAUTION

Before beginning to work, let the motors cool down. The thermal time

constant specified in the Technical Data is a measure for the time required

for cooling down. Cooling down can require up to 140 minutes!
Do not work at hot surfaces.
Wear safety gloves.

Cleaning

Excessive dirt, dust or shavings may affect the function of the motors

adversely, may in extreme cases even cause a failure of the motors. For that

reason, you should clean the cooling ribs of the motors in regular intervals (at

the latest, after one year is over).

Bearings

The nominal service life of the bearings is L10h > 30000 h (according to

DIN ISO 281, ed. 1990), if the permissible radial and axial forces are not

exceeded.
The motor bearings should be replaced, if
●

the nominal bearing service life has been reached

●

running noise can be heard

We recommend that you have the bearings replaced by Rexroth.

Connection Cables

Check connection cables for damage in regular intervals and replace them, if

necessary.
Check any optionally present flexible cable tracks for damage and replace

them, if necessary.

Danger to life by live parts with more than

50 V!

WARNING

Do not repair any connection cables provisionally. If the slightest damage is

detected in the cable sheath, you must immediately put the installation out of

operation and replace the connection cable.

Check the equipment grounding conductor for proper connection and tight fit

in regular intervals.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

361/407

Commissioning, operation, diagnostics and maintenance

R911335703_Edition 04 Bosch Rexroth AG

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды