Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 358

Страница: 358 / 422

LED

Color / status

Significance

Measures

H52.5

Drives

Green

No error at module bus, regular

status

None

Red

Module bus error (/Bb_A)

●

Check module bus wiring

●

Check control voltage supply of the

devices; see also "F2087 Module group

communication error"

Red/

green

Flashing

Drive system carries out error

reaction (Bb_A)

Bring device at module bus to readiness for

operation; see also diagnostic message "E2810

Drive system not ready for operation"

H53

42V Out

Green

Control voltage at output X53 okay None

Red

Control voltage at output X53 faulty

or control voltage outside of

tolerance
Error is saved until switch-off

Overload at output:
●

Check control voltage supply

●

Check voltage at X53

●

Reduce load

●

Remove short circuit

H54

DC Bus Out

Off

DC bus (L+, L-) not ready for power

output

None

Green

DC bus (L+, L-) ready for power

output

None

Red

DC bus voltage (L+; L-) at output

X54 not okay

Check fuses F4, F5 and replace them, if

necessary

Tab. 11-3:

KCU02 LED displays

344/407

Commissioning, operation, diagnostics and maintenance

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта, Страница: 358 / 422

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы: