Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 180

Страница: 180 / 422

Devices with communication out‐

put coupling

Information for devices with connection points for com‐

munication (e.g., X108/X109 or X118/X119)

●

The cover may only be removed from the housing

in vertical upward direction and placed onto the

housing in vertical downward direction.
Never rotate the cover while placing it back onto

the housing and tightening the screws. Otherwise,

the plug-in connections might be damaged.

●

At the bottom of the cover with the connection

points there is a circuit board.
Always leave this circuit board at its place.

Otherwise, the seals (O‑rings) might fall out of the

cover.

●

Before placing the cover back onto the housing

and tightening the screws:
Ensure that the circuit board with the connection

points is still correctly plugged in under the cover.

Tab. 6-22:

Cover with connection points

166/407

Connection points

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды