Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 236

Страница: 236 / 422

Power supply to KSM/KMS (KCU)

A drive line for power supply in the IndraDrive Mi system is designed as a

bus (L+, L-) and consists of:
●

X54 connector at KCU

●

RKH hybrid cable

●

X103.1 and X103.2 connectors at KSM/KMS

●

RHS0014 terminal connector at KSM/KMS

Comply with UL rating I

Bypass

In the case of equal load, the greatest load of the hybrid cable is

on the first cable segment.
In the drive line, place powerful KSM/KMS as near as possible to

the output of the drive connection box KCU.
Observe the maximum allowed bypass current I

Bypass

in each

segment (see

technical data of KSM

technical data of KMS

If necessary, install more KCU devices.

Available power at drive line

Available power P

KCU_strang

at a drive line:

KCU_strang

Available power at drive line

out

Output voltage, depending on supply unit

out_max

Output current; see

technical data of KCU

Fig. 7-6:

Available power at KCU drive line

With a small number of KSM/KMS and a low degree of power consumption in

a drive line (operation at partial load), the measurable value I

strang

at the

output of KCU is above the value which would result from the calculation of

the power P

of KSM/KMS and U

out

of KCU. The deviation is due to reactive

currents. The influence of these currents is insignificant in operation under

rated conditions.

Continuous power

Comply with continuous power
The sum of the electric powers of all KSM/KMS of a drive line

should not exceed the calculated value P

KCU_strang

of the KCU

drive connection box.

LN_nenn

Nominal power KSM/KMS

KCU_strang

Available power at drive line

Fig. 7-7:

Checking the continuous power

Instead of P

LN_nenn

, it is allowed to use the actually occurring

continuous power of the KSM/KMS.
Taking the average speed and simultaneity factor into account,

the sum of the installed rated motor powers therefore can be

significantly higher with servo operation.

222/407

Notes on project planning

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды