Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 296

Страница: 296 / 422

9.3

KMS

9.3.1

Required steps to follow

Preparations for mounting

Make the following preparations for mounting:

1. Procure tools, auxiliary materials, measuring and test equipment.
2. Check all components for visible damage. Defective components

mustn't be mounted.

3. Ensure that dimensions and tolerances on the installation side are

suitable for attachment (for details, see dimensional drawing).

4. Check whether all components, mounting surfaces and threads are

clean.

5. Ensure that mounting can be done in a dry and dust-free environment.

Mounting KMS

Notes on mounting

To allow trouble-free servicing, make sure that the following aspects are

fulfilled after KSM has been mounted:
●

Connection points are easily accessible

●

Address selector switches are easily accessible

●

Diagnostic LED is visible

Preferably mount the device to a conductive surface. If this is

impossible, later on connect the second connection point of equipment

grounding conductor at the device to the equipment grounding system

of the installation.

For devices of the "W" and "A" cooling types, only the mounting position

G1 is allowed.

For the dimensions of the mounting holes, see the dimensional drawing

of the device.

Data of the mounting screws:
Devices of "B" or "I" cooling type:
●

Thread: M5

●

Tightening torque: 6 Nm

Devices of "A" or "W" cooling type:
●

Thread: M6

●

Tightening torque: 6 Nm

Cold plate

Devices of cooling type "B" are mounted on a cold plate.
Required cold plate properties:
See

chapter 9.1.3 "Cold plate" on page 279

282/407

Mounting and installation

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды