Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 359

Страница: 359 / 422

11.3.3

KSM/KMS diagnostic display

LED H14

LED at device

Fig. 11-3:

LED H14 (KSM example)

At the device, there is a tricolor LED which displays the drive status.

Diagnostic display with MPx-17/18

H14

Color / flashing

pattern

Significance (drive status)

Measures

Off

Supply unit not switched on

Check and, if necessary, switch on the 24-V

supply

Cable interrupted

Check cable and connector X18

Hardware defective

Replace hardware

Flashing green Drive is error-free (phases 2, 3 and 4); in

phase 4, drive is ready for drive enable ("Bb")

If necessary, read exact status via "S‑0‑0095,

Diagnostic message"

Green

Power on and DC bus voltage available

("Ab")

Drive is error-free in operation and runs according

to inputs

Drive in control ["AF", "AH" or drive command

active (Cxxxs)]

Flashing green-

yellow

Switching command active (C01xx/C02xx)
Switching command error (C01xx/C02xx)

If necessary, read exact status via "S‑0‑0095,

Diagnostic message"

Firmware update running
Loader active

Do not interrupt the 24-V supply and do not unplug

connectors while the firmware is being updated

Drive command error (Cxxxx)

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

345/407

Commissioning, operation, diagnostics and maintenance

R911335703_Edition 04 Bosch Rexroth AG

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды