Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 363

Страница: 363 / 422

LED H26, displays
Ethernet/IP

LED: Color / flashing pattern Significance

Off

The device does not have a valid IP address or has been switched off.

Flashing green

The device has run up with a valid IP address, but does not have a cyclic connection.

Permanently lit green

The I/O connection has been established without error.

Flashing red

The existing I/O connection was unexpectedly aborted (e.g., watchdog).

Permanently lit red

The "Duplicate-IP-Adress-Check" showed that the IP address which was set already exists

in the network.

Flashing red-green

The device is running up and carries out a self test.

Tab. 11-6:

Diagnostic LED

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

349/407

Commissioning, operation, diagnostics and maintenance

R911335703_Edition 04 Bosch Rexroth AG

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды