Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 355

Страница: 355 / 422

11.3

Diagnostic functions

11.3.1

KMV diagnostic display

LED H14

Fig. 11-1:

LED H14

At the device, there is a bicolor LED which displays the status.

LED

Color / flashing pattern

Significance

Measures

Off

Supply unit not switched on

Check 24V supply and switch it on, if not yet done

Cable interrupted

Check cable and connector

Hardware defective

Replace hardware

Flashing green

Firmware update active

●

Transition command active

●

PM (parameter mode)

●

bb (control section ready for oper., mains

voltage not available)

●

ZKS (DC bus short circuit)

●

Ab (drive ready for operation, power on)

●

Bb (control section and power section ready for

operation, mains voltage available)

●

charg (DC bus charging active)

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

341/407

Commissioning, operation, diagnostics and maintenance

R911335703_Edition 04 Bosch Rexroth AG

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды