Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 374

Страница: 374 / 422

●

The holding brake is released after the system has been booted up

(

H14 LED

flashing).

The "release holding brake" service function may only be used

provided that communication with other drive components or with

an Engineering tool has not been established.
With operational communication established, the holding system

check command can be used to release the holding brake

(parameter "P‑0‑0541, C2100 Holding system check command").

11.4.6

Saving Parameters

For servicing, the drive parameters must be saved and archived on initial

commissioning (e.g. with software Rexroth IndraWorks D) because it must be

expected that the parameters of the defective drive cannot be read any

longer.
Parameters can be managed in the control unit or saved and loaded with the

"Rexroth IndraWorks D" software.

11.4.7

Firmware Update

See Functional Description of firmware → "Firmware Replacement".

11.4.8

Replacing the programming module

The programming module sits underneath a cover of the housing (see

chapter 6.3.4 "X107, programming module" on page 165

The programming module contains the firmware and parameters so that the

drive can be easily programmed during commissioning. Use the "Rexroth

IndraWorks D" software to configure the data transfer from the programming

module after the control voltage has been switched on.

360/407

Commissioning, operation, diagnostics and maintenance

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды