Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 360

Страница: 360 / 422

H14

Color / flashing

pattern

Significance (drive status)

Measures

Flashing yellow Drive warning (E2xxx … E3xxx)

Read exact status via "S‑0‑0095, Diagnostic

message" and execute service function

Communication warning (E4xxx)

Travel range warning (E6xxx … E7xxx)

Drive controller identification

Yellow

Fatal warning (E8xxx)

Do not interrupt the 24-V supply and do not unplug

connectors while the firmware is being updated

Flashing red-

yellow

Drive is error-free (phase 0), but not yet

ready for drive enable ("Bb")

If necessary, read exact status via "S‑0‑0095,

Diagnostic message"

Drive is error-free (phase 1), but not yet

ready for drive enable ("Bb")
Communication error (F4xxx)

Flashing red-

green

Baud rate scan (P‑1)

If necessary, read exact status via "S‑0‑0095,

Diagnostic message"

Flashing red

Error (F2xxx, F3xxx, F6xxx, F7xxx, F8xxx)

Read exact status via "S‑0‑0095, Diagnostic

message" and execute service function

Firmware update:

Repeat firmware update

Red

Booting phase

Wait until booting phase is over (approx. 2

minutes)

System error (F9xxx, E0800)

●

Switch off and on; replace hardware, if

necessary

●

Check whether the programming module is

inserted; if necessary replace KSM/KMS

crosswise to check whether the

programming module is defective

A square in the illustrated flashing patterns corresponds to a

time period of 250 ms.

Tab. 11-4:

LED Displays H14

Diagnostic display with MPx-2x

See

tab. 11-2 "LED displays" on page 341

346/407

Commissioning, operation, diagnostics and maintenance

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды