Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 291 | Manualshive

Страница: 291 / 422

background image

9

Mounting and installation

9.1

Introduction

9.1.1

Important notes

Safety

Injuries caused by live parts! Lifting of heavy

loads!

WARNING

Install the motors only when they have been de-energized and are not

connected electrically.
Use suitable lifting gear, protective equipment and protective clothing during

transport.
Observe the safety instructions contained in the preceding chapters.

Carry out all working steps with particular care. In this way, you minimize the

risk of accidents and damages.

Qualified technical staff

Any work at the installation and the drives or in their vicinity may be carried

out only by appropriately trained technical staff.
Make sure that all persons carrying out installation work, maintenance work

or operational activities at the installation are adequately familiar with the

contents of this documentation, as well as with all warnings and

precautionary measures contained therein.
Qualified technical staff must be trained, instructed and qualified to switch

electrical circuits and devices on and off in accordance with technical safety

regulations, to ground them and to mark them. Qualified technical staff must

possess appropriate safety equipment and have been trained in first aid.

Handling the devices

Injuries or damage and invalidation of the

warranty due to improper handling!

CAUTION

Avoid mechanical stressing, throwing, tipping or dropping of the products.
Use only suitable lifting gear.
Use suitable protective equipment and protective clothing during transport.

Wear safety shoes.
Protect the products against dampness and corrosion.

At delivery, the output shafts have protective sleeves and the connection

points have covers. During transport and storage, the protective sleeves and

covers must be attached to the device.
●

Remove the protective sleeves just before mounting.

●

Also use the protective sleeves if you return the goods.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

277/407

Mounting and installation

R911335703_Edition 04 Bosch Rexroth AG

«
...
289
290
291
292
293
...
»

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: Valve Concepts Страницы: 16

Бренд: Sabaj Страницы: 12

Бренд: ZKTeco Страницы: 18

Бренд: Hamworthy Страницы: 10

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: Jetline Страницы: 58

COOPER POWER SERIES

Бренд: Eaton Страницы: 50

Бренд: M-Audio Страницы: 26

Бренд: M Climate Страницы: 12

Q-SYS Core 110f

Бренд: QSC Страницы: 2

Бренд: Xylem Страницы: 48

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды