Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 357

Страница: 357 / 422

11.3.2

KCU02 diagnostic display

Fig. 11-2:

LEDs at KCU02

LED

Color / status

Significance

Measures

H49

Safety

Green

Safety technology signals without

error

None

Red

Safety technology signals with error
(Error is saved until the device is

switched off.)

Check safety technology wiring for short circuit.

H52.1

E-Stop

Off

E-Stop not activated

None

Red

E-Stop active (/E_Stop)

Deactivate E-Stop, if necessary (see connection

point X50)

H52.2

Power Supply

Green

Supply unit without error, regular

status

None

Red

Supply unit signals error (/Bb_V)

Check power supply, see also "F2086 Error

supply module"

H52.3

Warning

Green

Supply unit without warning

(/Warn), regular status

None

Red

Supply unit signals warning

Check supply unit, see also "E2086 Prewarning

supply module overload"

H52.4

DC Bus In

Off

DC bus voltage (L+; L-) too low

Switch power on at supply unit

Module bus not connected (if H54

green)

Connect module bus (connection point X1)

Green

DC bus voltage (L+; L-) without

error (Ud), regular status

None

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

343/407

Commissioning, operation, diagnostics and maintenance

R911335703_Edition 04 Bosch Rexroth AG

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды