Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 376

Страница: 376 / 422

Holding Brake – Commissioning and Maintenance Instructions

In order to ensure proper functioning of the holding brake, it must be checked

before the motors are commissioned. The test as well as the resurfacing may

be carried out "mechanically by hand" or "automatically by means of the

software function".

Checking and resurfacing of hold‐

ing brakes by hand

Measure the holding torque (M4) of the holding brake. If necessary, resurface

the holding brake.

Measuring the Holding Torque (M4) of the Holding Brake

De-energize the motor and secure it against re-energization.

Measure the transferable holding torque of the holding brake with a

torque wrench. For holding torque (M4) refer to the technical data.
If the holding torque (M4) is achieved, the motor is ready for assembly.

If the holding torque (M4) is not achieved, the subsequent resurfacing-

process can be used to reconstitute the holding torque.

Resurfacing the Holding Brake

At closed holding brake, turn the output shaft by hand, e.g. with the help

of a torque wrench, by about 5 revolutions.

Measure the holding torque (M4).
If the holding torque (M4) is achieved, the motor is ready for assembly.

If the specified holding torque (M4) is not attained after several grinding-

in processes, the holding brake is not operable. Please, contact the

Rexroth Service.

Checking and resurfacing of hold‐

ing brakes by means of the soft‐

ware function

Checking the Holding Torque (M4) via P-0-0541, C2100 Command

Holding system check

The efficiency of the holding brake and the opened state are checked by

the control device by starting the routine "P-0-0541, C2100 Command

Holding system check".
If the holding brake is operational, the drive is in an operational state

after the routine was run through. If the braking torque is too low, the

control device outputs a corresponding message.

The brake test can also be carried out cyclically in the framework

of a preventive maintenance.

Restoring the Holding Torque (M4) by means of the Software Function

The following possibilities are available:
1.

Realization of the resurfacing routine IndraDrive "Restoring the holding

torque "(see"P-0-0544, C3900 Command Resurfacing of motor holding

brake"). A repeated realization of the resurfacing routine is possible.
Upon the execution of the command C3900 it is not checked whether

the resurfacing of the holding brake was successful. It is recommended

to execute the command C2100 (Command Holding system check)

once again.

Resurfacing routine by superior control. Here, special control programs

adapted to the machine and system concepts are required. If necessary,

please contact your Bosch Rexroth distribution partner and discuss the

resurfacing routine parameters for your application.

362/407

Commissioning, operation, diagnostics and maintenance

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды