Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 301

Страница: 301 / 422

Personal injury or property damage by

interrupting or connecting live lines!

WARNING

Interrupting or connecting live lines may cause unpredictable dangerous

situations or lead to property damage. Therefore:
●

Connect and disconnect plug-in connectors only when they are dry and

de-energized.

●

During operation of the installation, all plug-in connectors must be

locked.

Risk of short circuit caused by liquid coolant

or lubricant!

WARNING

Short circuits of live lines may cause unpredictable dangerous situations or

lead to property damage. Therefore:
●

Provide exposed mating sides of power plug-in connectors with safety

caps when installing or replacing drive components, if you cannot

exclude that they might be moistened with liquid coolant or lubricant.

9.6.2

Notes

The motor cable is a hybrid cable in which the communication line has been

integrated. Only the hybrid cable by Rexroth can ensure the function. It is

supplied as ready-made cable. The outgoing direction of the hybrid cable

cannot be changed subsequently!

Risk of damage by subsequently changing

the outgoing direction of the hybrid cable!

NOTICE

Do not try to reverse the cable outgoing direction of a ready-made connector!

The flexible leads in the connector have individual lengths for each outgoing

direction.

Risk of damage by leakage of the connection

points!

NOTICE

If vibrations affect the hybrid cable: Install strain relief near the connection

points (X103.1, X103.2) so that the connectors are not affected by high

vibration loads. This can avoid possible leakage (entering liquid).

When ordering the ready-made hybrid cables, always indicate the desired

outgoing direction: See

chapter 5.9.1 "RKH hybrid cable incl.

communication, technical data" on page 114

Ready-made hybrid cables have been coded in such a way that X103.1 and

X103.2 cannot be interchanged when connecting the cables.

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

287/407

Mounting and installation

R911335703_Edition 04 Bosch Rexroth AG

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды