Bosch Rexroth IndraDrive Mi KCU02 Скачать руководство пользователя страница 192

Страница: 192 / 422

6.3.8

Second connection point of equipment grounding conductor

Parts of the installation with attached KSM0x/KMS0x have to be connected to

the equipment grounding system of the installation. The housings of KSM0x/

KMS0x then are connected to the equipment grounding system of the

installation via the flange. This connection is required in addition to the

equipment grounding conductor in the hybrid cable, because the leakage

current of a KSM0x/KMS0x servo drive is greater than 3.5 mA.
Additionally connect the KSM0x/KMS0x housing via a second equipment

grounding conductor to the equipment grounding system of the installation, if

KSM0x/KMS0x is attached to parts of the installation which
●

have bad electroconductive properties
or

●

cannot be connected to the equipment grounding system of the

installation.

High housing voltage and high leakage

current! Danger to life, risk of injury from

electric shock!

WARNING

Connect the second connection point of equipment grounding conductor at

KSM0x/KMS0x to the equipment grounding system of the installation, if the

electric resistance between the mechanical holder of the flange and the

equipment grounding system of the installation is greater than 5 ohm.
If you would like to measure the resistance, the following conditions

previously must have been complied with:
●

The installation has been switched off
(This avoids parasitic leakage currents.)

●

The hybrid cables have not been connected to the drive
(This disables the first equipment grounding connection via the hybrid

cable.)

Risk of damage to the devices by spark

discharge of static charges

NOTICE

In some applications (e.g., printing or packaging), high static charges can

develop. Make sure that these charges can be directly discharged against

ground at their point of origin. Therefore, connect the

second connection

point of equipment grounding conductor

of the devices to the equipment

grounding system of the installation.

The first equipment grounding conductor is routed via the hybrid

cable from X103.1 / X103.2 (KSM0x/KMS0x) to the connection

point X54 (KCU02) and connected to the equipment grounding

system of the installation via KCU02.

178/407

Connection points

IndraDrive Mi Drive Systems with KCU02, KSM02,

KMS02/03, KMV03, KNK03, KLC03

Bosch Rexroth AG R911335703_Edition 04

Содержание Rexroth IndraDrive Mi KCU02







































































































































































































































































































































































































































Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды

Bosch Rexroth IndraDrive Mi KCU02, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth IndraDrive Mi KCU02

Отзывы:

Похожие инструкции для Rexroth IndraDrive Mi KCU02

Бренды по названию

Популярные бренды