BARTEC BENKE DPA-4.5 Скачать руководство пользователя страница 119

Страница: 119 / 158

Distillation Process Analyzer DPA-4.5

Faults

Fault

Possible cause

Troubleshooting

No ready signal /
measuring result for a
long time

Unsuitable parameter settings

Adjust the parameters
(see software handbook).

Signal cable connection to device has been
interrupted.

Rectify the cause of the fault.

Outputs with
measured values
assume unusual or
implausible values /
measuring result
repeatability or
reproducibility
worsens.

Fault in product conditioning (dirt, water or gas in
product, product temperature...)

Make sure that the product is
treated in accordance with the
technical data specifications.

The measured values for the fill level fluctuate
significantly.

Re-adjust the bubble gas
pressure regulator.

Alarm at digital alarm
output

PACS has issued an alarm.

Rectify the cause of the alarm.
Perform a reset (see software
handbook).

The device is switched off.

Switch on the device.

PACS is not running.

Start PACS (see software
handbook).

Insufficient or no
product flow (see
display on flow
controller).

−

Product supply line

: shut-off valve is closed,

primary pressure too low, leakage, product has
run out, filter is blocked

−

Analyzer

: product has run out, leakage

−

Drain

: blocked, shut-off valve closed

Rectify the cause of the fault
(e.g. blocked filter). Make sure
that the product is treated in
accordance with the technical
data specifications.

Product flow too great The flow controller is defective.

Replace product flow controller.

Distillation flask is not
filled / filled very
slowly with product

The metering pump is not working properly or is
defective.

Check the power connection.

Check/replace the metering
pump.

Distillation flask is not
heated / not heated
sufficiently

The fuse or ground fault circuit breaker of the
power supply have tripped.

Find and rectify the cause of
the fault

Distillation flask only
cools down very
slowly

The fan is defective

Replace fan.

No cold product is flowing through the distillation
flask:

Insufficient or no product flow in the product supply
line.

Draining the sample is impossible.

See above

See below

The sample is not

The outlet filter is blocked.

Clean the outlet filter

December 2013

119

Содержание DPA-4.5































































































































































Результаты поиска

Содержание DPA-4.5

Отзывы:

BARTEC BENKE DPA-4.5, Руководство по эксплуатации, Страница: 119 / 158

Результаты поиска

Содержание DPA-4.5

Отзывы: