AL-Car BC 4535, Руководство пользователя

Страница: 17 / 240

GB 6
Important:
Remove the shoulder strap from the appli-
ance before you start the engine.
5 STARTING UP
5.1 Fuel and oil:
1. The engine of the power scythe is a 2-stroke en-
gine. For operation, it requires a mixture of normal
unleaded petrol and 2-stroke oil in a ratio of 25:1
(see fuel mixture table).
2. It is advisable to mix a maximum of 5 litres of
petrol/oil mixture, since this quantity will give you
approx. 12-15 operational hours and an older pet-
rol/oil mixture does not guarantee the optimum
level of lubrication.
Never use pure petrol for your appliance.
Otherwise there is a danger of causing per-
manent damage to the engine and as a result
the manufacturer's guarantee would not ap-
ply. Do not use any petrol/oil mixture which
has been kept for longer than 90 days.
Only use a petrol/oil mixture in a mixing ratio
of 25:1. Do not change the mixing ratio of your
own accord even if some types of 2stroke oil
recommend a different mixing ratio. If insuffi-
cient
Fuel mixture table:
Fuel 2-stroke oil
1 l (1000 cm³) 0,040 l (40 cm³)
3 l (3000 cm³) 0,120 l (120 cm³)
5 l (5000 cm³) 0,200 l (200 cm³)
5.2 Starting the engine:
Important
: You must first read the instructions for star-
ting the engine from a cold and a warm state, and then
carry out the appropriate start procedure. Place the
appliance on a hard, level surface, hold it by the han-
dle with one hand and pull the starting handle on the
tension cable with the other hand.
Important
: In order to keep the load on the engine as
small as possible during start-up and warm-up, cut the
excess cutting line back to 13cm.
5.2.1 Starting the engine from a cold
1. Set the ignition switch (1) to the "Start" position.
2. Secure the throttle lever: Press the "Lock off”
switch (2) downward. Then, at the same time,
press the throttle lever (3) and slide the locking
switch (4). The throttle lever locks into place on
full throttle.
3. The appliance has a choke, which can been set in
2 positions: "CHOKE (
) and „RUN“ ( ) ). Set
the choke lever to "CHOKE" ( ).
4. For starting purposes, spray fuel into the carburet-
tor. Press the pad ten times.
5. Pull the starting cable out by a short amount, until
you feel resistance (approx. 10cm). For a strong
ignition spark, a smooth, sharp pull is required.
Pull the starting cable four times quickly and
forcefully.
6. Set the choke lever to "RUN" ( )
.
7. If the engine does not start up, repeat steps 1 to
6.
PLEASE NOTE:
If the engine does not start up even
after several attempts, read the section "Engine Trou-
bleshooting”.
PLEASE NOTE:
Always pull the starting cable out in a
straight line. If it is pulled out at an angle, then friction
will occur on the eye. As a result of this friction, the
cable will become frayed and will wear away faster.
Always hold the starter handle when the cable retracts.
Never allow the cable to snap back when it has been
pulled out. This would fray or wear the cable and also
damage the starter unit.
5.2.2 Starting the engine from a warm state
1. Set the ignition switch to the "Start” position.
2. Set the choke lever to the "RUN" ( ) position.
3. Lock the throttle lever as described under Point 2
of "Starting the engine from a cold state”.
4. Pull the starter cable quickly, until the engine
starts up. However, do not pull the cable more
than 6 times. Hold down the throttle lever FULLY,
until the engine is running quietly. If the engine
does not want to start, set the choke to "RUN"
(
)and pull 5 more times on the starter cable.
However, should the engine not start, then it is
probably fully-pumped with petrol. Wait 5 minutes
and then try it again with the choke set to "RUN"
and with a fully depressed throttle lever.