Agilent Technologies U1401B Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 181

background image

IV

U1401B User’s and Service Guide

General Safety Information

The following general safety precautions must be observed during all
phases of operation, service, and repair of this instrument. Failure to
comply with these precautions or with specific warnings elsewhere in this
manual violates safety standards of design, manufacture, and intended
use of the instrument. Agilent Technologies assumes no liability for the
customer’s failure to comply with these requirements.

WA R N I N G

• When working above DC 60 V, AC 30 Vrms or AC 42.4 Vpeak, exercise caution

– these ranges pose a shock hazard.

• Do not measure more than the rated voltage (as marked on the instrument)

between terminals, or between terminal and earth ground.

• Double-check the instrument operation by measuring a known voltage.
• This instrument is designed for measurement under CAT II 150 V. Avoid

measuring power mains with voltage exceeding 150 V.

• For current measurement, turn off circuit power before connecting the

instrument to the circuit. Always place the instrument in series with the
circuit.

• When connecting probes, always connect the common test probe first. When

disconnecting probes, always disconnect the live test probe first.

• Detach test probes from the instrument before you open the battery cover.
• Do not use the instrument with the battery cover or part of the cover removed

or loose.

• Recharge or replace the battery as soon as the low battery indicator

flashes on screen. This is to avoid false readings, which may lead to possible
electric shock or personal injury.

• Do not use the instrument if it is damaged. Before you use the instrument,

inspect the casing. Look for cracks or missing plastic. Do not operate the
instrument around explosive gas, vapor, or dust.

• Inspect the test probes for damaged insulation or exposed metal, and check

for continuity. Do not use the test probe if it is damaged.

• Do not use any other AC charger adapter apart from the one certified by

Agilent with this product.

• Do not use repaired fuses or short-circuited fuse-holders. For continued

protection against fire, replace the line fuses only with fuses of the same
voltage and current rating and recommended type.

• Do not service or perform adjustments alone. Under certain condition,

hazardous voltages may exist, even with the equipment switched off. To avoid
dangerous electric shock, service personnel must not attempt internal service
or adjustment unless another person, capable of rendering resuscitation or
first aid, is present.

«
...
2
3
4
5
6
...
»

Содержание U1401B






















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для U1401B

Simple Logger II CL601

Бренд: AEMC Страницы: 48

Integra 27 Series

Бренд: Keithley Страницы: 52

Onset HOBO UX100-001

Бренд: ALAT UJI Страницы: 7

Бренд: Ranger Страницы: 27

Бренд: AST Страницы: 12

HWM PermaNET SU

Бренд: FCS Страницы: 10

Бренд: Huato Страницы: 15

Бренд: Canary Systems Страницы: 38

Бренд: Canary Systems Страницы: 69

Бренд: Observator Страницы: 4

Бренд: red lion Страницы: 8

Бренд: Sutron Страницы: 22

Бренд: Seneca Страницы: 4

Бренд: Seneca Страницы: 8

Бренд: Seneca Страницы: 8

Бренд: Seneca Страницы: 40

Бренд: Seneca Страницы: 54

Бренд: Seneca Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды