Agilent Technologies U1401B Скачать руководство пользователя страница 179

Страница: 179 / 181

Specifications

U1401B User’s and Service Guide

155

Output Specifications

Accuracy is given as ± (% of output

counts of least

significant digit) at 23 °C ± 5 °C, with relative humidity less
than 80% R.H., and warmed up for at least five minutes.

Constant voltage and constant current outputs

[1]

The maximum input voltage protection is 30 VDC.

[2]

Loading coefficient: 0.012 mV/mA for 1.5 V output.

[1]

The maximum input voltage protection is 30 VDC.

[2]

Loading coefficient: 1

A/ V, the minimum output voltage is based on 20 mA into a 600

load.

[3]

If the current loop has a 24 V power, a minimum output voltage of 24 V is achievable with a 20 mA current in a 1200

load.

This is only applicable for the simulation mode for mA output, refer to

“Simulation Mode for mA Output”

on page 88 for more

information.

Table 8-16

Constant voltage (CV) output specifications

Function

Range

Resolution

Accuracy

Maximum output

current

[2]

Constant

voltage (CV)

[1]

± 1.500 V

0.1 mV

0.03% + 3

25 mA or below

± 15.000 V

1 mV

Table 8-17

Constant current (CC) output specifications

Function

Range

Resolution

Accuracy

Maximum output

voltage

[2]

Constant

current (CC)

[1]

± 25.000 mA

0.03% + 5

12 V or below

[3]

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство, Страница: 179 / 181

Результаты поиска

Содержание U1401B

Отзывы: