Agilent Technologies U1401B Скачать руководство пользователя страница 50

Страница: 50 / 181

U1401B User’s and Service Guide

Calibrator Output Operations

Constant Current Operation

The U1401B can generate a constant current output in the
range of ±25 mA.

To select the constant voltage output function:

Turn the rotary switch to any one of the

(constant

current output) positions.

Press

SHIFT

to access the shifted operations of the keypad.

The

annunciator will appear on the display.

Press

MODE

to cycle through ±25 mA,

±25 mA, and

±25 mA output modes. Select the ±25 mA output

mode for constant output (or steady output, as opposed to

autoscan

autoramp

outputs, which will be discussed

under

“Memory Generation”

on page 31).

•

Unlike the autoscan and autoramp modes, there is no
special annunciator on the display to indicate constant
current (CC) operation.

With the instrument in standby mode (you should see the

annunciator on the display; if not, press

OUTPUT

), you

can adjust the amplitude of the output by pressing

and

to select the digit to be adjusted, and then

pressing

and

to adjust the value of the selected

digit.

Press

OUTPUT

to start the source output. The

annunciator will appear on the display.

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды