Agilent Technologies U1401B Скачать руководство пользователя страница 72

Страница: 72 / 181

U1401B User’s and Service Guide

Making Measurements

To measure temperature, follow these steps:

Set the slide switch to the

position to disable the

output.

Turn the rotary switch to the

position

Press and hold

for more than 1 second to select

temperature measurement.

Plug the thermocouple adapter (with the thermocouple
probe connected to it) into the positive and negative input
terminals (

Figure 3- 4

on page 53).

Touch the surface to be measured with the thermocouple
probe.

Read the display.

If you are working in a constantly varying environment,
where the ambient temperature is not constant, follow these
steps:

Press

to select 0 °C compensation. This allows a

quick measurement of the relative temperature.

Avoid contact between the thermocouple probe and the
surface to be measured.

After a constant reading is obtained, press

to set

the reading as the relative reference temperature.

Touch the surface to be measured with the thermocouple
probe.

Read the display for the relative temperature.

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство, Страница: 72 / 181

Результаты поиска

Содержание U1401B

Отзывы: