Agilent Technologies U1401B Скачать руководство пользователя страница 164

Страница: 164 / 181

144

U1401B User’s and Service Guide

Performance Tests and Calibration

Output calibration

Set the slide switch to the

M/S

position.

Allow the instrument to warm up for 10 minutes before
performing calibration.

To enter the calibration mode, press

and

for

more than one second. The primary display will indicate
“CHEEP”.

Press

to enter the input calibration mode.

Turn the rotary switch to any one of the “Current
Input/Voltage Output” positions, and press

SHIFT

for more

than one second to enter the output calibration mode.

CAL-0 & CAL-1

In the output calibration mode, the primary and secondary
display will show “CAL- 0” and “- rdy- ” respectively.

Connect the output terminals to a multimeter (refer to

Table 7- 1

on page 131 for the recommended test

equipment).

•

CAL-0

Press

OUTPUT

. The primary and secondary displays

show “CAL- 0” and “00000” respectively.

Wait until the instrument reading becomes stable, then
record the value.

•

CAL-1

Press

MODE

. The primary and secondary displays show

“CAL- 1” and “- rdy” respectively.

Press

OUTPUT

. The primary and secondary displays

show “CAL- 1” and “00000” respectively.

Press

to adjust the output voltage until the

reading on the meter is the same as the

CAL-0

value

recorded above.

Press

MODE

to finish the

CAL-0

and

CAL-1

calibration.

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды