Agilent Technologies U1401B Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 181

background image

Calibrator Output Operations

2

U1401B User’s and Service Guide

35

Defining the autoscan parameters in the memory

Press and hold

MODE

for more than one second to enter the

autoscan adjustment mode. A total of 16 steps with
individually definable time interval and amplitude are
available.

When the instrument is in the autoscan adjustment mode,
the secondary display shows the amplitude. The first two
digits of the primary display are used to indicate which step
is being adjusted. The last two digits of the primary display
are used to indicate time interval.

1

Press

MODE

to cycle through step, time interval, and

amplitude adjustments. The digit to be adjusted will flash
on the display.

•

For amplitude adjustment, press

and

to select

the digit to be adjusted, and then press

and

to

adjust the value of the selected digit. The amplitude
can be set to any value within the selected output
range (±1.5 V or ±15 V for constant voltage output, ±25
mA for constant current output).

•

For time interval adjustment, press

and

to

select the digit to be adjusted, and then press

and

to adjust the value of the selected digit. The time

interval can be set within the range of 0 to 99 seconds.

•

Press

for more than one second to directly reset

the time interval and amplitude of the present step to
zero.

«
...
53
54
55
56
57
...
»

Содержание U1401B






















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для U1401B

Бренд: Elitech Страницы: 2

Бренд: Jetter Страницы: 66

Бренд: B+B Sensors Страницы: 18

Бренд: exemys Страницы: 85

Бренд: ZANDER Страницы: 22

Бренд: Solare Datensysteme Страницы: 506

Apollo IV DT304

Бренд: UEi Страницы: 20

Бренд: GRAPHTEC Страницы: 22

Бренд: Hobo Страницы: 7

Бренд: PCE Health and Fitness Страницы: 14

DeltaBlack 71614

Бренд: ETM Страницы: 2

Бренд: Simex Страницы: 112

Бренд: Solvera Lynx Страницы: 17

StowAway-IS Temp

Бренд: Onset Computer Corporation Страницы: 4

Бренд: FIBRO Страницы: 22

Бренд: AED Electronics Страницы: 6

Бренд: az-instrument Страницы: 45

Бренд: UGCS Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды