Agilent Technologies U1401B Скачать руководство пользователя страница 30

Страница: 30 / 181

U1401B User’s and Service Guide

Getting Started

Figure 1-5

Keypad shifted functions

Table 1-4

Keypad functions

No.

Key

Function when pressed for less than one
second

Function when pressed for more than one
second

Selects DC, AC, or AC+DC

Toggles between peak hold ON or OFF for V
and mA measurement

HOLD

If the data hold mode is enabled:

Freezes the present measured value. Press
again to trigger the next measured value.

Exits data hold mode

[1]

If the refresh hold mode is enabled:

Enters or exits the refresh hold mode

–

MAX MIN

[2]

Cycles through MAX, MIN, AVG, and present
(MAX AVG MIN) readings in dynamic
recording mode

Enters or exits the dynamic recording mode

[1]

NULL

Saves the displayed value as a reference to be
subtracted from subsequent measurements

Toggles between mV and temperature tests

RANGE

Changes measurement range

Sets to autorange

DUAL

Cycles through different combinations of
primary and secondary displays

–

Selects frequency (Hz), duty cycle (%), or pulse
width (ms) on the primary display

Exits selection

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство, Страница: 30 / 181

Результаты поиска

Содержание U1401B

Отзывы: