Agilent Technologies U1401B Скачать руководство пользователя страница 135

Страница: 135 / 181

Application Examples

U1401B User’s and Service Guide

115

Frequency Transmitter Verification

For some frequency transmitters, you can use the square
wave output as a source simulator and measure the current
from the transmitter output.

Turn the rotary switch to the

position.

Press

MODE

to cycle through duty cycle, pulse width,

output level, and frequency adjustments.

Set the output frequency to 150 Hz and duty cycle to 50%.

Connect the probe leads between the input terminals of
the U1401B and the output terminals of the transducer.

Connect

the alligator leads between the output terminals

of the U1401B and the input terminals of the transducer.
Make sure the polarity is correct.

Press

OUTPUT

to output the signal.

Read the display. Check the measured current to
determine whether the frequency is consistent with the
transducer specifications.

Change the square wave frequency and monitor the
measured current on the display.

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство, Страница: 135 / 181

Результаты поиска

Содержание U1401B

Отзывы: