Agilent Technologies U1401B Скачать руководство пользователя страница 122

Страница: 122 / 181

102

U1401B User’s and Service Guide

Application Examples

Determining transistor h

For NPN-type BJT

Turn the rotary switch to the

position.

Connect the base to the positive output terminal.

Connect the emitter to the negative output terminal and
the negative terminal of a DC power supply (which
supplies the required V

Connect the collector to the negative input terminal.

Connect the positive terminal of the DC power supply to
the positive input terminal through a resistor.

Output a constant current of +1.000 mA (this is I

Read the measured current value (this is I

For PNP-type BJT

Turn the rotary switch to the

position.

Connect the base to the positive output terminal.

Connect the collector to the negative output terminal and
the positive terminal of a DC power supply (which
supplies the required V

Connect the emitter to the negative input terminal.

Connect the negative terminal of the DC power supply to
the positive input terminal through a resistor.

Output a constant current of - 0.500 mA (this is I

Read the measured current value (this is I

The transistor h

is calculated as the ratio of I

over I

N O T E

If you wish to obtain the correct results, please adjust the values of V

and I

according to the conditions specified by the transistor

manufacturer.

Содержание U1401B






















































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Agilent Technologies U1401B, Руководство пользователя и сервисное руководство, Страница: 122 / 181

Результаты поиска

Содержание U1401B

Отзывы: